LWX7E8611B USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................5 3. INSTALLATION............................................................................................................7 4. PRODUCT DESCRIPTION.........................................................................................11 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety- Gulf Market WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • Do not install the appliance behind a lockable door, a sliding door or a door with a hinge on the opposite side, that would prevent the appliance door from being fully open. Connect the mains plug to the mains socket only at the end of the installation process. Make sure that the mains plug is accessible after installation. The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ENGLISH • • • • • • • • • • 5 Do not use the appliance if items have been soiled with industrial chemicals. Do not dry unwashed items in the wash dryer. Items such as foam rubber (latex foam), shower caps, waterproof textiles, and rubber backed articles and clothes, or pillows fitted with foam rubber pads should not be dried in the washer dryer. Fabric softeners, or similar products, should only be used as specified by the product manufacturer’s instructions.
www.aeg.com • • • • • the drum to prevent an internal damage. Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear. Do not install or use a damaged appliance. Do not install the appliance where the appliance door cannot be fully opened. Adjust the feet to have the necessary space between the appliance and the flooring. When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level.
ENGLISH 7 3. INSTALLATION WARNING! Refer to Safety chapters. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. 3.1 Unpacking WARNING! Remove all the packaging and the transit bolts before installing the appliance. WARNING! Use the gloves. 1. Remove the external film. If necessary, use a cutter. 5. Carefully put the appliance down on its rear side. 6. Put the front polystyrene packaging element on the floor under the appliance.
www.aeg.com 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Positioning and levelling 1. Install the appliance on a flat hard floor. Make sure that carpets do not stop the air circulation below the appliance.
ENGLISH A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. When the machine is installed on a plinth or if a washer dryer is stacked on the washing machine, use the accessories described in chapter 'Accessories'. Read carefully the instructions supplied with the appliance and with the accessory. 9 4. Connect the water inlet hose to the cold water tap with 3/4" thread.
www.aeg.com You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. It is possible to connect the drain hose in different ways: 1. Make a U shape with the drain hose and put it around the plastic hose guide. 2. On the edge of a sink - Fasten the guide to the water tap or to the wall. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.
ENGLISH 6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp. 4. PRODUCT DESCRIPTION 4.
www.aeg.com 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Time Drying Cottons Cottons Eco Synthetics Delicates Wool/Handwash Outdoor Anti-Allergy NonStop 60min Steam Rinse Temp. Stains Spin Prewash Spin Wash 12 5.
ENGLISH Maximum load indicator. The icon flashes during laundry load estimation (refer to "PROSENSE load detection" paragraph). Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. If you run a programme when the drum is overloaded, end of the programme. also flashes at the Drying time indicator. Door locked indicator. The digital indicator can show: , washing and/or drying phase). • Programme duration (e. g. • Delay time (e. g. or ).
www.aeg.com 6. DIAL AND BUTTONS 6.1 On/Off Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. As the Stand-by function automatically deactivates the appliance to decrease the energy consumption in a few cases, you may need to activate the appliance again. For more details, refer to Stand-by paragraph in Daily Use chapter. 6.
ENGLISH This option is not available with a temperature lower than 40 °C. • Prewash Use this option to add a pre-wash phase at 30 °C before the washing phase. This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles. The options can increase the programme duration. 6.6 Delay Start 6.8 Time Drying Touch this button to set the time that suits the fabrics you have to dry (refer to "Timed drying" table). The display shows the set value.
www.aeg.com 7. PROGRAMMES 7.1 Programme Chart Programme Programme description Washing programmes Cottons Cottons Eco White cotton and coloured cotton. Normal, heavy and light soil. White cotton and fast-coloured cotton. Normal soil. The energy consumption decreases and the time of the washing programme is extended, ensuring good washing results. This programme at 60 °C with a load of 8 kg is the reference programme for energy label data, in compliance with UAE. S 5010 2:2013.
ENGLISH 17 Programme Programme description NonStop 60min Complete programme composed of a washing phase and of a drying phase for a small load of mixed fabrics (cotton and synthetic items). appears on the display. Also, the indicator Steam programme Steam programmes2) Steam Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry softer. Do not use any detergent.
www.aeg.com Programme Default tempera- Reference spin ture speed Temperature Spin speed range range Maximum load Synthetics 40 °C 60 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg Delicates 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg Wool/Handwash 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.
Prewash ■ ■ ■ ■ Stains2) ■ ■ ■ ■ ■ Delay Start ■ ■ ■ ■ Quick Wash3) ■ ■ ■ ■ Time Drying ■ ■ ■ ■ Auto Drying ■ ■4) ■ ■ ■ ■ 19 Rinse ■ ■ Steam ■ NonStop 60min Delicates ■ Anti-Allergy Synthetics ■ Outdoor Cottons Eco ■ Options Extra Rinse Wool/Handwash Cottons Programme ENGLISH ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Before setting this option, select a suitable washing programme for the garments.
www.aeg.com 7.2 Woolmark Apparel Care Blue • The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as "hand wash" provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1230 • The wool drying cycle of this machine has been tested and approved by The Woolmark Company.
ENGLISH 21 7.
www.aeg.com 9. SETTINGS 9.1 Child Lock With this option you can prevent that the children play with the control panel. • To activate/deactivate this option, touch the Spin and the Stains/ Prewash buttons simultaneously until the indicator comes on/goes off on the display. You can activate this option: • After you touch the Start/Pause button: all the buttons and the programme dial are deactivated (except On/Off button ). • Before you touch the Start/Pause button: the appliance cannot start.
ENGLISH Make sure not to put too much laundry in the drum. 4. Close the door firmly. CAUTION! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 10.3 Filling the detergent and additives 23 Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results.
www.aeg.com 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. The indicator of the Start/Pause button flashes.
ENGLISH The PROSENSE estimation starts at the end of the countdown. 25 At the end of the load detection, in case of drum overload, the indicator flashing in the display: is Cancelling the delay start after the countdown has started In this case, for 30 seconds, it is possible to pause the appliance and remove the exceeding garments. To cancel the delay start: Once removed the exceeding garments, touch the Start/Pause button to start the programme again.
www.aeg.com 10.10 Interrupting a programme and changing the options When the programme is running, you can change only some options: 1. Touch the button Start/Pause. The related indicator flashes. 2. Change the options. The given information in the display changes accordingly. 3. Touch the button Start/Pause again. The washing programme continues. 10.11 Cancelling a running programme 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2.
ENGLISH 10.14 Draining water out after end of cycle If you have chosen a programme or an option that does not empty out the water of the last rinse, the programme is completed, but: • The display shows the door locked indicator • The drum still turns at regular intervals to prevent the creases in the laundry. • The door stays locked. • You must drain the water to open the door: 1. If necessary, touch the Spin button to decrease the spin speed proposed by the appliance. 2.
www.aeg.com 3. Put the detergent and the additives in the appropriate compartment. 4. Turn the programme dial to the washing programme. The display shows the default temperature and spin. If necessary, change them according to your laundry. The display also shows the maximum recommended load for washing phase. 5. Set the desired options, if there are available. 6. Touch the Mode button once to activate also the drying function. The Wash and Dry indicators come on.
ENGLISH 29 After drying phase, clean the drum, the seal and the inside of the door with a wet cloth. 12. DAILY USE - DRYING ONLY WARNING! Refer to Safety chapters. This appliance is an automatic washer dryer. 12.1 Preparation to drying 1. Press the On/Off button for some seconds to activate the appliance. With a drying-only programme the display does not show the maximum load and the PROSENSE estimation is deactivated. 2. Load the laundry one item at a time. 3.
www.aeg.com • The indicator of button Start/Pause goes off. The door locked goes off • Press the button On/Off for some seconds to deactivate the appliance. After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically. 1. Remove the laundry from the appliance. 2. Make sure that the drum is empty. After drying phase, clean the drum, the seal and the inside of the door with a wet cloth. 13.
ENGLISH • Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ). • A very small load can cause balance problems with the spin phase leading to excessive vibration. If this occurs: a. interrupt the programme and open the door (refer to "Daily Use" chapter); b. manually redistribute the load so that the items are spaced evenly around the tub; c. press the Start/Pause button. The spin phase continues. 14.
www.aeg.com • Garments with foam-rubber or materials similar to foam-rubber. 14.8 Garment labels When you dry the laundry, obey the indications on the labels of the manufacturers: • = The item can be tumble dried • = The drying cycle is at high temperature • = The drying cycle is at reduced temperature • = The item can not be tumble dried. 14.
ENGLISH 15.3 Maintenance wash The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew. To eliminate these deposits and hygienize the inner part of the appliance, run a maintenance wash regularly (at least once a month): 1. Remove all laundry from the drum. 2. Run a cotton programme with the highest temperature with a small quantity of powder detergent. 33 15.
www.aeg.com WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 1. Open the pump cover. 2 1 15.7 Cleaning the drain pump WARNING! Disconnect the mains plug from the mains socket. 2.
ENGLISH 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 35 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 1 12. Close the pump cover. 1 2 8. If it is necessary, remove fluff and objects from the filter recess. 9.
www.aeg.com 15.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 15.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph.
ENGLISH 37 16. TROUBLESHOOTING WARNING! Refer to Safety chapters. 16.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: • - The appliance does not fill with water properly.
www.aeg.com Problem The appliance does not fill with water properly. Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the inlet hose has no kinks, damages or bends. • Make sure that the connection of the water inlet hose is correct.
ENGLISH 39 Problem Possible solution The appliance makes an unusual noise and vibrates. • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". • Add more laundry in the drum. The load may be too small. The programme duration • The ProSense function is able to adjust the programme duincreases or decreases ration according to the type and the laundry load size.
www.aeg.com 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull the emergency unlock trigger downward once. Pull it downward once again, keep it tensed and, in the meanwhile, open the appliance door. CAUTION! Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down. CAUTION! Risk of injury! Make sure that the drum is not rotating.
ENGLISH Programmes Load (kg) Cottons Eco 60 °C Cottons energy saving pro- 41 Energy Water conApproximate proconsump- sumption (li- gramme duration tion (kWh) tre) (minutes) 8 0.90 60 250 Cottons 40°C 8 1.25 80 200 Synthetics 40°C 4 0.78 55 130 Delicates 40°C 4 0.60 63 91 1.5 0.35 57 60 gramme1) Wool/Handwash 30°C 1) This programme at 60 °C with a load of 8 kg is the reference programme for energy label data, in compliance with UAE. S 5010 2:2013. 18.
www.aeg.com 19. ACCESSORIES 19.3 Pedestal with the drawer 19.1 Available in www.aeg.com/shop or from authorised dealer Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. 19.2 Fixing plate kit If you install the appliance on a plinth, secure the appliance with the fixing plates. Read carefully the instructions supplied with the accessory.
ENGLISH 43
157022840-A-302018 www.aeg.
