LWX8C1612W USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................6 3. INSTALLATION............................................................................................................7 4. PRODUCT DESCRIPTION.........................................................................................11 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • The appliance shall be installed as a freestanding product or below the kitchen worktop if space margins permit. Do not install the appliance behind a lockable door, a sliding door or a door with a hinge on the opposite side, that would prevent the appliance door from being fully open. Connect the mains plug to the mains socket only at the end of the installation process. Make sure that the mains plug is accessible after installation.
ENGLISH • • • • • • • • • • • 5 Items that have been soiled with substances such as vegetable or mineral oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed separately with an extra amount of detergent before being dried in the washer dryer. Do not use the appliance if items have been soiled with industrial chemicals. Do not dry unwashed items in the wash dryer.
www.aeg.com 2. SAFETY INSTRUCTIONS 2.1 Installation The installation must comply with relevant national regulations. • Follow the installation instructions supplied with the appliance. • Do not install or use the appliance where the temperature can be less than 0°C or where it is exposed to the weather. • Always keep the appliance vertical when being moved. • Make sure that there is air circulation between the appliance and the floor. • Remove all the packaging and the transit bolts.
ENGLISH WARNING! Risk of injury or damage to the appliance. • Do not sit or stand on the open door. • Do not dry dripping wet clothes in the appliance. 2.5 Disposal • Disconnect the appliance from the mains electrical and water supplies. 7 • Cut off the mains electrical cable close to the appliance and dispose of it. • Remove the door catch to prevent children or pets from becoming trapped in the drum.
www.aeg.com 7. Remove the polystyrene protection from the bottom. 10. Remove the three bolts by using the key supplied with the appliance. 1 2 8. Pull up the appliance in vertical position. 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 11. Pull out the plastic spacers. 12. Put the plastic caps, that you find in the user manual bag, in the holes.
ENGLISH WARNING! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 2. Position it toward left or right depending on the position of the water tap. 45 20 x4 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation.
www.aeg.com A If this occurs, close the water tap and contact the authorized service centre to replace the hose. 3.5 Water drainage The drain hose should stay at a height of not less than 60 cm and not more than 100 cm. You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3.
ENGLISH 5. Without the plastic hose guide, to a sink spigot - Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration. 6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp. Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. 4. PRODUCT DESCRIPTION 4.
www.aeg.com 5. CONTROL PANEL 5.
ENGLISH 13 Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. Detergent quantity indicator: the value shows the percentage of detergent quantity needed. Child safety lock indicator. Drying time indicator. Door locked indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. or , washing and/or drying phase). ). • Cycle end ( ). • Warning code (e.g. ).
www.aeg.com Pre-wash indicator. Stain indicator. ECO Energy saving indicators. It appears when you set the 棉织物节能 programme. Delay start indicator. 6. DIAL AND BUTTONS 6.1 开/关 When the display shows the indicators Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. and , the appliance does not heat the water.
ENGLISH In some programmes the rinses are performed with more water. The display shows the indicator . The door stays locked. The drum turns regularly to reduce creasing. You must drain the water to unlock the door. Touch the 启动/暂停 button: the appliance performs only the draining phase. The appliance empties the water out automatically after approximately 18 hours. 6.5 去污/预洗 Press this button repeatedly to activate one of the two options. The relevant indicator goes on in the display.
www.aeg.com "Timed drying" table). The display shows the set value. Each time you touch this button the time value increases by 5 minutes. You cannot set all time values for different types of fabrics. 6.10 烘干等级 Touch this button to set one of 3 automatic dryness levels proposed by the appliance. On the display the relevant dryness indicator goes on: • • ironed. Iron dry: laundry to be Cupboard dry: laundry to be put in store. • Extra dry: laundry to be fully dried.
ENGLISH Programme 户外 17 Programme description Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or inner insulation. By performing a non-stop wash and dry programme, the drying phase also acts as waterrepellent restorer. Make sure that the garment care label permits tumble drying.
www.aeg.com Programme Programme description 脱水/排水 To spin the laundry and to drain the water in the drum. All fabrics, except woollens and delicate fabrics. 1) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or doesn't rotate properly, but this is normal for this programme. 2) If you set a Steam programme with dried laundry, at the end of the cycle the laundry could be humid.
ENGLISH 19 精细 羊毛/手洗 户外 连续洗干 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 脱水/排水 化纤 ■ 漂洗 棉织物节能 ■ 蒸汽 棉织物 Programme Programme options compatibility ■ ■ Options 脱水 Rinse Hold Extra Silent ■ ■1) No Spin Extra Rinse 预洗 去污2) 延时启动 省时3) 防皱 烘干时间 烘干等级 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■4) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) If you set No Spin option, the appliance only drains the water.
www.aeg.com 7.2 Woolmark Apparel Care Blue • The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as "hand wash" provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1144 • The wool drying cycle of this machine has been tested and approved by The Woolmark Company.
ENGLISH 21 7.
www.aeg.com 9. SETTINGS 9.1 Child Lock With this option you can prevent that the children play with the control panel. • To activate/deactivate this option, touch the 去污/预洗 and the 延时启动 buttons simultaneously until the indicator comes on/goes off on the display. You can activate this option: • After you touch the 启动/暂停 button: all the buttons and the programme dial are deactivated (except 开/关 button ). • Before you touch the 启动/暂停 button: the appliance cannot start.
ENGLISH The indicator of 启动/暂停 button flashes. 2. Turn the programme knob to the necessary programme. The programme indicator comes on. The display shows the maximum load, the default temperature, the maximum spin speed, the indicators of the phases making up the programme and the programme duration. 3. If it is necessary, touch the 温度 button and the 脱水 button to change the water temperature and the spin speed. 4. If necessary, touch the related buttons to add some options and/or to set a delayed start.
www.aeg.com Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results. 4. To use liquid detergent, turn the flap down. After a washing cycle, if necessary, remove any detergent residue from the detergent dispenser. 10.
ENGLISH 25 1. Touch the 启动/暂停 button to pause the appliance. The related indicator flashes. 2. Touch the 延时启动 button repeatedly until the display shows . 3. Touch the 启动/暂停 button again to start the programme immediately. Changing the delay start after the countdown has started To change the delay start: Make sure that the flap does not cause a blockage when you close the drawer. 10.7 Starting a programme Touch the 启动/暂停 button to start the programme. The related indicator stops flashing and stays on.
www.aeg.com E.g. the washing or pre wash phase is . running: When the phase ends the relevant indicator stops flashing and is steady on. The next phase indicator starts flashing. E.g. the rinse phase is running: .
ENGLISH After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance. 2. 3. 4. 5. When you activate the appliance again, the display show the end of the last selected programme. Turn the programme dial to set a new cycle. Remove the laundry from the appliance. Make sure that the drum is empty. Keep the door and the detergent dispenser slightly ajar to prevent mildew and odours. Close the water tap. 10.
www.aeg.com 11.1 NON-STOP programme Wash and dry Not all programmes are compatible with drying function. The 连续洗干 programme is already a complete wash&dry programme. You can wash and dry your laundry setting a «non stop-programme». Proceed as follows: 1. Press the 开/关 button for some seconds to activate the appliance. 2. Turn the programme dial to the desired washing programme. The display shows the default temperature and spin. If necessary, change them according to your laundry.
ENGLISH • In the display comes on. • The indicator of button 启动/暂停 goes off. The door locked goes off • Press the button 开/关 for some seconds to deactivate the appliance. 29 1. Remove the laundry from the appliance. 2. Make sure that the drum is empty. After drying phase, clean the drum, the seal and the inside of the door with a wet cloth. After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically. 12.
www.aeg.com Each time you tap on this button the time value increases by 5 minutes. The display shows the set new time value. 2. Touch the 启动/暂停 to start the programme. In the display the door locked indicator comes on and the indicator of the running phase starts flashing. The display also shows the remaining programme time. 12.4 At the end of the drying programme • The appliance stops automatically. • The acoustic signals operate (if they are active). • In the display comes on.
ENGLISH • Empty pockets and unfold. • Turn multilayered fabrics, wool and items with printed illustrations inside out. • Pre-treat tough stains. • Wash heavy soil stains with a special detergent. • Be careful with curtains. Remove the hooks and put the curtains in a washing bag or pillowcase. • Do not wash laundry without hems or with cuts. • Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ).
www.aeg.com 14.7 Items not suitable for drying Do not set a drying programme for this laundry: • Very delicate items. • Synthetic curtains. • Pieces of clothing with metal inserts. • Nylon stockings. • Quilts. • Bed covers. • Duvets. • Anoraks. • Sleeping bags. • Fabrics with residue of hair sprays, nail solvents or similar. • Garments with foam-rubber or materials similar to foam-rubber. 14.
ENGLISH The regular detergents already contain water softening agents, but we recommend to run a cycle with empty drum and a descaling product occasionally. Always follow the instructions that you find on the packaging of the product. 15.3 Maintenance wash The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew.
www.aeg.com WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 1. Open the pump cover. 2 1 15.7 Cleaning the drain pump WARNING! Disconnect the mains plug from the mains socket. 2.
ENGLISH 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 35 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 1 12. Close the pump cover. 1 2 8. If it is necessary, remove fluff and objects from the filter recess. 9.
www.aeg.com 15.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 15.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph.
ENGLISH 37 16. TROUBLESHOOTING WARNING! Refer to Safety chapters. 16.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the 启动/暂停 button may flash continuously: • - The appliance does not fill with water properly.
www.aeg.com Problem The appliance does not fill with water properly. Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the inlet hose has no kinks, damages or bends. • Make sure that the connection of the water inlet hose is correct.
ENGLISH 39 Problem Possible solution The appliance makes an unusual noise and vibrates. • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". • Add more laundry in the drum. The load may be too small. The programme duration • The ProSense function is able to adjust the programme duincreases or decreases ration according to the type and the laundry load size.
www.aeg.com After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the Authorised Service Centre. If the display shows other alarm codes. Deactivate and activate the appliance. If the problem continues, contact the Authorised Service Centre. 16.3 Emergency door opening To open the door, proceed as follows: In case of power failure or functioning failure the appliance door remains locked.
ENGLISH Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture IPX4 Water supply 1) Cold water Water supply pressure Minimum Maximum 0,5 bar (0,05 MPa) 8 bar (0,8 MPa) Maximum wash load Cotton 10 kg Maximum dry load Cotton Synthetics 6 kg 4 kg Spin Speed Maximum 1600 rpm 41 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 18. ACCESSORIES 18.
Groups Washer Dryers * X X X X Air duct (including filter) Hydraulics (including hoses, pressure switch, electrovalves, pumps) Control Panel Door (including hinge and door lock) Hg Cd Cr6+ Hazardous substances PBBs PBDEs 1. This table is compiled according to SJ/T11364-2014. means this kind of hazard substance content in all the homogenous material of this part is under the limitation regulated 2. in GB/T26572-2011. 3.
ENGLISH 43
157010901-A-132018 www.aeg.