User manual

14. Montera det nedersta gångjärnet
(E) på motsatta dörrsidan och fäst
det med de tidigare borttagna
skruvarna. Montera fast hålskyd-
det (G) på det nedre gångjärnet.
15. Drag ut täckbiten (F) från ventila-
tionsgallret (D) och montera den
på motsatta sidan.
15. Sätt tillbaka ventilationsgallret.
Såväl det mellersta som det övre
gångjärnet kan utnyttjas för att
justera in dörrarna.
Det mellersta gångjärnet kan justeras horisontellt sedan de båda
skruvarna lossats med hjälp av ett verktyg.
Det mellersta gångjärnet kan justeras sedan muttern lossats med en
10 mm nyckel. Gå tillväga som visas på bilden.
10
Före start
• Rengör skåpets inre och alla utrustningsdetaljer före första start (se
avsnittet “Rengöring och slötsel”).
Elektrisk anslutning
För den elektriska anslutningen krävs ett föreskriftsenligt installerat
skyddskontakt-vägguttag.
Den elektriska säkringen måste uppgå till minst 10 Ampere.
När vägguttaget inte längre är åtkomligt efter skåpets uppställning
måste med hjälp av en lämplig åtgärd i den elektriska installationen
säkerställas att skåpet vid behov kan göras strömlöst (t.ex. genom
säkring, LS-brytare, felström-skyddsbrytare eller dylikt med en kon-
taktöppningsvidd på minst 3 mm).
• Före igångsättning skall det på skåpets typskylt kontrolleras om
anslutningsspänning och strömart stämmer överens med nätets
värden på uppställningsplatsen.
t.ex: AC 220 ... 240 V 50 Hz eller
220 ... 240 V~50 Hz
(dvs. 220 till 240 Volt växelström, 50 Hertz)
Typskylten finns på vänster sida inuti skåpet.
PR228
35
Defrosting
Refrigerator
Frost is automatically eliminated from the evaporator of the refrigera-
tor compartment every time the motor compressor stops, during nor-
mal use. The defrost water drains out through a trough into a special
container at the back of the appliance, over the motor compressor,
where it evaporates.
Freezer
The freezer compartment, however, will become progrssively covered
with frost. This should be removed with the special plastic scraper
provided, whenever the tickness of the frost exceeds 4 mm. During
this operation it is not necessary to switch off the power supply or to
remove the foodstuffs.
However when the ice becomes very thick on the inner liner, comple-
te defrosting should be carried out as follows:
1. Remove the frozen food from
the freezer, wrap it in several
layers of newspaper and put it
in a very cool place.
2. Switch off the appliance and
pull out the plug, or remove or
unscrew the safety fuses.
3. Leave the freezer compart-
ment door open.
4. Insert the plastic scraper into
the recess provided under the
defrost water channel and pla-
ce a collecting basin under it.
5. Once defrosting is completed keep the scraper for future use;
6. Turn the thermostat knob to the required setting or replace the plug in
the power socket.
Warning!
Never use metal tools to scrape off the frost
Do not use a mechanical device or any artificial means to speed up the
thawing process other than those recommended by the manufacturer.
A temperature rise of the frozen food packs, during defrosting , may
shorten their safe storage life.