Operation Manual

5 ENGLISH
TECHNICAL DATA
Voltage range .........................7,2-18 V
Quick charge current ...................1,7 A
Maintaining charge .......................50 mA
Battery charging time
1,4 Ah ............................approx 60 min
1,7 Ah ............................approx 70 min
2,0 Ah ............................approx 80 min
2,4 Ah ..........................approx 100 min
Weight without cable ..................490 g
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Do not dispose of used battery packs in the household refuse
or by burning them. AEG Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System 3000 chargers for charging System 3000
battery packs. Do not use battery packs from other systems.
The following battery packs can be charged with this charger:
voltage battery rating No. of
(of storage battery) battery
cells
7,2 V B 7.2-range
1,4 Ah 6
9,6 V B 9.6-range
1,4 Ah 8
12 V B 12-range
1,2 Ah 10
14,4 V B 14.4-range
1,4 Ah 12
18 V B 18-range
1,4 Ah 15
Do not try to charge non-chargeable batteries with this
charger.
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Never break open battery packs and chargers and store only
in dry rooms. Keep dry at all times.
Please pay attention to the following symbol on the label of
the charger:
This tool is only suitable for indoor use. Never expose
tool to rain.
The battery clamps of the charger are fed by the mains
supply. Do not touch the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new
one.
Before use check machine, cable, and plug for any damages
or material fatigue. Repairs should only be carried out by
authorised Service Agents.
SPECIFIED CONDITIONS OF USE
The quick charger can charge AEG batteries from
9.6 V to 18 V.
Do not use this product in any other way as stated for normal
use.
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the
design conforms to safety class II.
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
General note concerning NiMH batteries:
The capacity of the battery is reduced when the temperature
falls below -10°C.
Long-term storage at temperatures higher than +40°C may
have negative effects on the capacity of the battery.
CHARACTERISTICS
After inserting the battery into the reception of the charger the
battery will automatically be charged (control lamp is
illuminated continuously)
If the battery is too hot (over approx .45°C) the charger
switches to maintenance charge. Remove battery, allow to
cool down and insert again.
If the battery is too cold (less than approx. 0°C) no charging
takes place. After warming up of the battery charging takes up
automatically; the battery can stay in the charger.
The battery’s charging time is between 10 min and 60 min (at
1,4 Ah), depending on the state of discharge.
The battery can be stored permanently in the charger without
the danger of being overcharged.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60335, EN 55014-1, EN 55014-2, EN 61000-
3-2, EN 61000-3-3, in accordance with the regulations 73/23/
EEC, 89/336/EEC
Rainer Warnicki
Manager Product Marketing
and Development
MAINTENANCE
If the supply cord of this appliance is damaged, it must only
be replaced by a repair shop appointed by the manufacturer,
because special purpose tools are required
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
The battery clamps of the charger are fed by
mains supply. do not touch the tool with
conducting objects.
Please read the instructions carefully before
starting the machine.