Before using for the first time First of all sot the time of day on the timer After connection of the contort pane! to the power supply {and after power cuts} the display in the electronic timer will flash “00.00". With a sharp pens or ballpoint depress the button recessed In the center of the selector switch {see Figure 1/Arrow), Al the same time set the time of day with the knob. As soon as the correct time of day appears in the display release the button. The time is now set.
Using the hotplates Saving energy when cooking Figure 2 The tensile has a flat reinforced base and the wienie base and the hotplates are the same size. This ensures optimum transfer of heat trim the hotplate to the utensil. G Wasting electricity when cooking Figure 3/A The utensil is too small for this hotplate, Figure 3/B The base of the utensil is not flat. Figure 3/C The lid is not on properly. Hints for cooking on hotplates ® Protect your hotplates rom moisture otherwise the plates will start to rust.
Using the hotplates General The word "hotplate” is used here o mean both cast horror hotplates and ceramic radiant areas. The control pane of your cooker has two automatic hotplates (Figaro 4/4) and two high speed hotplates (Figure one of which Is a dual circuit high speed hotplate (figure 4/8). G The symbols beside the switches indicate which knob belongs to which hotplate.
Using the hotplates Automatic hotplate settings Switch setting Recommended for 12 Heating up large quantities of water, bailing nobodies 1112 Deep frying chips, browning meat, for example goulash 1011 Frying, for example potato pancakes, sirloin, steaks, » cordon big 410 Frying meat, escalopes, chops, pancakes, rissoles, making a oux 89 Slow frying, sausages, liver, eggs, fritters 57 Booting large quantities of food, stews and soups 46 Simmering potato, cooking meat broth 35 Simmering vegetables or stewing
How the electronic timer works @ The times are set by pressing the corresponding display (D). When the button is. pounding button (3 and simultaneously turn released the time of day will appear again. ing During setting the times will Significance of symbols Push buttons with symbols () Symbols In display (D Setting the alarm time. You can check the settings by means of 45 () Setting durst on of baiting or frying the twa symbols AUTO and ¢ : time.
How to use the electronic timer ) Resetting time of day After a power failure the hotplates will be inoperative. The display will flash “00:00". Set the time of day; only after this has been done can you use the hotplates again. How 10 do this will be found under “Be tore using for the first tme™, page 15 Setting the alarm The alarm operates independently of a program set or in operation with the automatic timer. You can therefore use it purely as an alarm (setting a signal without any switching function).
How to use the electronic timer G Setting the automatic preset (switch on and switch off} 1. Switch on automatic hesitates as usual. 2. Turn selector switch to automatic setting. The AUTO indicator will flash, 3. Seeing duration of cooking time Press button [(Bland at the same time set the required duration of bailing or frying time with the knob. Then release button. The time of day wiki reappear in lhe splashy The AUTO indicator and the ¢ g indicator will imitative continuously. 4.
Cleaning and care General Turn the hotplates off before cleaning and alto them to cool down, Then remove any fad remains with a damp cloth and a fettle liquid soap. Never use abrasive pot scourers, coarse scouring powder, rust or stain removers or bleaches. Do riot place aluminum golf over the hotplates. Hotplates Remove stubborn dirt from the hotplates with fine scaring powder or pad. Afterwards warm up gently and allow to dry.
What (something doesn’t work) he indicator fights do not come on? ® Perhaps you have not set all the switches necessary o1 ® the fuse has blown. the display in the timer flashes 00.007 1. Ba fore using ford the thirst time the time of day must be set. Only then will the hotplates unction, See page 15 under “First of ail set the ime of day on the timer™. 2. Power failure, After a pow failure the tire of day and the times et have been canceled.