SANTO 2992-4i no-frost Integrierbare Einbau Kühl-Gefrierkombination Integrating Fridge Freezer Gebrauchs- und Einbauanweisung Operating and Installation Instructions
Dear customer, Before placing your new refrigerator/freezer into operation please read these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance. Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . 27 Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Installation . . . . . . . . . . . . . . . . . . . . . .
Safety The safety aspects of our refrigerators/freezers comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, we consider it our obligation to make you aware of the following safety information: Intended use • The refrigerator is intended for use in the home. It is suitable for the cooling, freezing and storing of frozen food, as well as for making ice.
mains plug, cut off the mains cable, break or remove spring or boltcatches, if fitted. By doing this you ensure that children cannot lock themselves in the fridge when playing (there is risk of suffocation!)or get themselves into other dangerous situations. • Often children cannot recognise the hazards present in household appliances.
Disposal Appliance Packaging Information All materials are environmentally sound! They can be dumped or burned at an incinerating plant without danger! About the materials: The plastics can be recycled and are identified as follows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
• Remove pins (A) and (B). A • Remove all adhesive tape and packing pieces from the interior of the appliance. C D B Installation Installation Location The appliance should be set up in a well ventilated, dry room. Energy use is affected by the ambient temperature.
If installation next to a source of heat is unavoidable, the following minimum clearances must be maintained at the sides of the appliance: – for electric cookers 3 cm; – for oil and coal fired ranges 30 cm. If these clearances cannot be maintained a heat insulating pad is required between the cooker and the refrigeration appliance.
P A D B C D C P1 D337 Left opening 1. Remove pin “P” and the door. 2. Remove (A) from the left side and (B-C-D) from the right side. 3. Refit (B-C-D) on the left side and (A) on the right side. 4. Refit door and “P” on the left side. 5. Remove “P1” from the right side. Housing dimensions Height Depth Width 1780 mm 550 mm 560 mm Instructions for total built-in Push appliance into the housing until stop strip (A) touches the kitchen unit.
If after having carried out the previously described operation there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). A D265 Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position.
Apply covers (B) on joint cover lugs and into hinge holes. B D726 Position the runners (A) at the top and bottom of the inside of the kitchen unit as shown in Fig. and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3.5x16 mm screws. A 20m m PR33 Open both the appliance door and that of the kitchen unit to approx. 90°. Place the little plates over the runners.
Remove the little plates and make the holes with a diam. of 2 mm. Replace the little platee over the runners and screw in the screws provided (3.5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly.
The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Important! The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Earth Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the terminals in your plug, proceed as follows: 1.
-how often the door is opened The temperatures in the refrigerator compartment and freezer co partment cannot be independently regulated. If you want the freeze fresh food rapidly, select setting „6“, ensuring that the temperature in the refrigerator compartment does not drop blow 0°C. You should also promptly reset the temperature regulator to setting „3“ or „4“. Important! High ambient temperatures (e.g.
• To do this pull the storage shelf forward until it can be swivelled upwards or downwards and removed. • Please do the same in reverse to insert the shelf at a different height.Slide the front half of the Vario storage shelf in another level to the rear. By this means you will gain space to place tall items on the storage shelf below. Adjusting the upper door rack • Depending on the food stored, the upper door racks can be changed to other holders or removed.
Freezing and storing frozen food You can use your freezer for freezing fresh food yourself. Important! • The temperature in the freezer compartment must be –18 °C or colder before freezing food. • Please observe the freezing capacity given on the rating plate. The freezing capacity is the maximum quantity of fresh food that can be frozen within a period of 24 hours. If you wish to freeze food several days in a row, please observe a maximum capacity of only 2/3 to 3/4 of that on the rating plate.
2. When frezzing fresh food, depress theambient temperature switch (A) 24 hours before loading the food without modifying the thermostat setting. The pilot light will come on. At the end of the freezing process, do not forget to depress again the ambient switch in order to avoid an increase of the power consumption. 2. Place frozen foods in the drawers sorted by type, as far as possible. Riders are supplied for placing on drawers.
types of frozen goods. Whether the upper or lower value of the indicated storage time is valid depends on the quality of the foods and pre-treating before freezing. The lower value applies to foods with high fat content. • By attaching the included index-tabs to the drawers, they can be marked according to which type of foods the individual compartments contain.
4. Defrost freezer compartment and clean thoroughly (see section: “Cleaning and Care”). 5. Leave the door open to avoid the build up of odours. Cleaning and Care For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly. Warning! • The appliance may not be connected to the mains during cleaning. Danger of electrical shock! Before cleaning switch the appliance offand rem ve the plug from the mains, or switch off or turn out the circuit breaker or fuse.
Accumulation of dust at the condenser increases energy consumption. For this reason carefully clean the condenser at the back of the appliance once a year with a soft brush or a vacuum cleaner. 6. Check the water drain hole on the rear wall of the fridge. Clear a blocked drain hole with the aid of the green peg in the pack of accessories included with the appliance. 7. After everything is dry place appliance back into service.
Malfunction Possible Cause Remedy Appliance is not switched on Switch on the appliance. Mains plug is not plugged in Insert mains plug. or is loose. Appliance does not work. Fuse has blown or is defec- Check fuse, replace if tive. necessary. Socket is defective. Appliance cools too much. Mains malfunctions are to be corrected by an electrician. Temperature is set too cold. Turn the temperature regulator to a warmer setting temporarily..
Unusual noises. Appliance is not level. Readjust the feet. The appliance is touching the wall or other objects. Move the appliance slightly. A component, e.g. a pipe, If necessary, carefully bend on the rear of the appliance the component out of the is touching another part of way. the appliance or the wall. The compressor does not This is normal, no error has The compressor starts after start immediately after chan- occurred. a period of time. ging the temperature setting.
Customer Service If you cannot find the remedy for a malfunction in these operating instructions, please contact your dealer or our customer service department. Addresses and telephone numbers are listed in the accompanying booklet "Guarantee Conditions/Customer Service Locations". Selective ordering of replacement parts can save unnecessary travel and costs.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
