Operation Manual

English
45
ID3 (6 on the remote)
In case of a CD or file in the MP3 format:
Press the button to turn on the function. “ID3 ON” will show
in the display for a short time. In case of a stored ID-3 Tag in-
formation it will show up in the display as a continuing band.
Press the button again to deactivate the function. “ID3 OFF”
will show in the display for a short time.
PROG (10/4)
To save the stations and to set the programmed playback.
Program Playback
Program playback in desired sequence.
1. Press
STOP button (7/9).
2. Press PROG button (10/4). The display will show “- - - -
PR:01” (“track” PR: “memory position”) and MEMORY.
Use the / buttons (9/8) to select the desired track and
press PROG buttons again. The display will change to
memory position P02.
3. Use the
/ buttonstoselectthenexttrackandpress
PROG again. Repeat the steps until you have selected all
tracks.
NOTE:
If the memory capacity of the programmable title is
reached, “FULL” will be displayed.
4. Press the
PLAY/PAUSE button (8/11). Playback starts.
The display will show the first selected track number.
5. Press STOP button once to stop playback. The memory
will be kept.
6. For repeated playback of the programmes, press the
PLAY/PAUSE button.
7. To delete memory, please press STOP button twice.
MEMORY will no longer be displayed.
The device will stop automatically after all stored tracks have
been played. The program sequence will be kept in the
memory until you switch to another mode, remove the CD
from the compartment or switch off the device.
It is possible to combine program playback with the REPEAT
function. After programming and starting playback, please
press REPEAT button (6/13) up to three times; the functions
can be applied as described under “REPEAT“.
Playback of music files in MP3 format
This device allows the playback of music files in MP3 format.
The device furthermore supports the common CD types: CD,
CD-RW, and CD-R.
Your device can play MP3 CDs. These are compressed CDs
that can store up to 200 tracks. Your device automatically
recognizes MP3 discs (the display will show total number of
tracks and folders). Please refer to chapter “Playing CD/MP3”
for playback of such CDs. You may program tracks as already
described under “Program playback”.
Please note:
There are many burning and compressing methods, as well
as differences in quality of CDs and burnt CDs.
Furthermore,themusicindustrydoesnotapplyxedstan-
dards (copy protection).
For that reason there might, in rare cases, occur problems
when playing CDs and MP3 discs. That is not a malfunction
of this device.
Cleaning and maintenance
• Disconnectthemainsplugbeforecleaning.
• Youmaywipeoffexternalstains,usingaslightlydamp
cloth without any additives.
Troubleshooting
Symptoms Course Solution
CD can not be
played back.
CD is not inserted or
inserted incorrectly.
Ensure that the disc
is inserted with the
label facing upwards.
Batteries too weak. Insert new batteries
or operate the device
with the mains lead.
CD jumps dur-
ing playback.
Check the disc for
fingerprints, dirt or
scratches.
Check the disc for
fingerprints, dirt or
scratches.
The unit does
not work.
The unit is blocked
and “hangs”.
Disconnect the mains
plugforapproxi-
mately 5 seconds.
Then switch the unit
back on.
Volume (3)
and basses
(20) cannot be
adjusted on
the device.
The PROG but-
ton (10/4) was held
pressed down until
the time display ap-
peared. Then one
of the controls was
pressed while the
time was displayed.
Press any button to
release the lock of
the control.