User Manual

20 21ENGLISH
power tool or accessory is dropped, inspect for damage
or install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-load
speed for one minute. 

h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments.





i) Keep bystanders a safe distance away from work
area.Anyone entering the work area must wear
personal protective equipment.


j) Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting tool
may contact hidden wiring or its own cord.



k) Position the cord clear of the spinning accessory.


l) Never lay the power tool down until the accessory has
come to a complete stop.

m) Do not run the power tool while carrying it at your
side.

n) Regularly clean the power tool’s air vents.



o) Do not operate the power tool near fl ammable
materials.
p) Do not use accessories that require liquid coolants.


Kickback and Related Warnings
















a) Maintain a fi rm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up.

b) Never place your hand near the rotating accessory.

c) Do not position your body in the area where power
tool will move if kickback occurs. 


d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.


e) Do not attach a saw chain, woodcarving blade or
toothed saw blade. 

Safety Warnings Specifi c for Grinding and Abrasive
Cutting-Off Operations:
a) Use only wheel types that are recommended for your
power tool and the specifi c guard designed for the
selected wheel.

b) The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.



c) Wheels must be used only for recommended
applications. For example: do not grind with the side of
cut-off wheel. 


d) Always use undamaged wheel fl anges that are of
correct size and shape for your selected wheel.



e) Do not use worn down wheels from larger power
tools.

Additional Safety Warnings Specifi c for Abrasive
Cutting-Off Operations:
a) Do not “jam” the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth of
cut.


b) Do not position your body in line with and behind the
rotating wheel.


c) When wheel is binding or when interrupting a cut for
any reason, switch off the power tool and hold the
power tool motionless until the wheel comes to a
complete stop. Never attempt to remove the cut-off
wheel from the cut while the wheel is in motion
otherwise kickback may occur.

d) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter the
cut.

e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.



f) Use extra caution when making a “pocket cut” into
existing walls or other blind areas. 


ENGLISH
TECHNICAL DATA WS15-125SX WS15-125SXE
Angle Grinder
 




  
 









  

 

 
  
  
  
Noise/Vibration Information


  
  
Wear ear protectors!









 










 




WARNING









WARNING! Read all safety warnings and all
instructions

Save all warnings and instructions for future reference.
Angle Grinder SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush, or cut-off tool.Read all safety
warnings, instructions, illustrations and specifi cations
provided with this power tool. 


b) Operations as polishing are not recommended to be
performed with this power tool. 


c) Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.


d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power tool.


e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. 

f) The arbour size of wheels, fl anges, backing pads or
any other accessory must properly fi t the spindle of the
power tool.



g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If