User's Manual

ManualsBrandsAEI Protect-On Systems ManualsElectronicsSPLIT-DECODED ACCESS CONTROLLER

RF REMOTE CONTROLLER -- (DA-2800 ONLY)

The DA-2800 RF Remote Controller consists of a built-in receiver and two remote control keys, which has 4 channels

to control the Output Relay 1, 2, 3 and the built-in door chime. Two remote keys are supplied and up to 40 remote

keys can be accommodated by the system. The receiver (decoder) of the system learns the ID codes from the remote

keys. Each remote key contains a 24-bit ID code that provides over 1 million code combinations. The remote key gives

around 60 Meters of controlling distance in open space to the receiver.

(A) Procedure of Recording An RF Remote Key -- (Learning)

The RF remote keys that prepare to work with the decoder are required to be registered. The decoder learns the ID of the

remote keys one by one beforehand with the following procedures:

1) Press and hold the LEARN button on the receiver unit for 1 second until the REMOTE LED turns ON. (The button is

inside the hole. Use a pin or the tip of a ball pen to reach it). See Figure 1

2) The decoder of the receiver is in Waiting Mode for 10 seconds waiting for the signal from the Remote Key after

the Remote LED turning ON.

3) Press any button of the RF Remote Key unit ONCE within the 10 seconds for the receiver to learn the ID Code from it.

4) The REMOTE LED on the receiver unit turns OFF after the ID Code is learned.

5) Take the above learning procedures 1-4 for other RF Remote Keys

(B) Procedure of Deleting The RF Remote Keys from Memory -- (Clearing)

If an RF remote key is lost it is necessary to delete it from the memory of the receiver. Every time the system will clear

all the ID Codes of the RF Remote Keys in the deletion. Re-learn the existing remote keys are necessary.

1) Press and hold the LEARN button on the receiver unit for 8 seconds (Remote LED turns ON) until the REMOTE

LED gives 2 flashes to confirm that all the data are erased. Then the LED turns OFF.

2) Record the ID Code of the existing RF Remote Keys (not lost) into the memory again one by one with the

procedures stated in the “Recording An RF Remote Key”

The system can be operated with the RF Remote Control Keys no matter it is in Split-decoded Mode or in Standard

Alone Mode. In the Split-decoded mode, the RF Remote Key operates the system according to the functions and data

that have been programmed with the digital keypad. While in Stand Alone operation the system operates its outputs

according to the functions that stated in the Stand Alone Mode 1 or Mode 2.

1) Press button A to operate Output 1

2) Press button B to operate Output 2

3) Press button C to operate Output 3

4) Press button D to operate the built-in Door Chime

STAND ALONE MODE -- (DA-2800 ONLY)

The system that operates in Stand Alone mode does not require the keypad. It is directly controlled by the RF Remote

Key for the outputs. It is an ideal solution for the remote controls of door strike, alarm arm-disarm, garage door opening

etc.. The following settings are necessary while the system is in stand alone operation:

1) Put the “Function Mode Jumper” to position “2” or “3” for the desired Stand Alone Operation Mode. See the

“Function Mode Jumper Setting” stated above for the details.

2) Always put “Link-up Jumper” on OFF position.

3) Leave the “Data I/O” port open without any connection.

4) Make all the installation connections to the terminals of the decoder unit.

EXAMPLES – PROGRAMMING AND OPERATION

1) Example 1 -- EM Card Only :

i) Programming :

001

(a) (b)

(a) The card is programmed for operating of the Output 1

(b) The operation is EM Card only

(d) Put the card close to the reader to read it, one beep confirms the reading

(e) Press # to store the “Card” into memory, two-beep confirms a valid entry

ii) Operation : (while the system is back to operation mode)

(a)

a)Put the EM card close to the reader. Two-beep confirms the card is read and the Output 1 activates

2) Example 2 -- Private User PIN Only :

i) Programming :

001

1234

(a)

(b) (c) (d) (e)

(a) The Private User PIN is programmed for operating of the Output 2

(b) The operation is Private User PIN only

(d) Put Private User PIN “1 2 3 4” into the storage location

(e) Press # to confirm and store the “Private User PIN” into memory, two-beep confirms a valid entry

ii)Operation : (while the system is back to operation mode)

1234

(a) (b)

(a) Key in the Private User PIN “1 2 3 4”

(b) Confirm it with the # key. Output 2 activates

3) Example 3 -- EM Card + Secondary User PIN :

i) Programming :

002

24680

(a) (b) (c) (d) (e) (f)

(a) The card is programmed for operating of the Output 1

(b) The operation is EM Card + Secondary User PIN

(d) Put the card close to the reader. One beep confirms the reading

(e) Put Secondary User PIN “2 4 6 8 0” into the storage location

(f) Press # to store the “Card + Secondary User PIN” into memory, two-beep confirms a valid entry

ii) Operation : (while the system is back to operation mode)

24680

(a) (b) (c)

(a) Put the EM card close to the reader. Two-beep confirms the reading and 30 seconds waiting time is given for the

entry of the User PIN, the Amber LED keeps flashing

(b) Key in the Secondary User PIN “2 4 6 8 0”

Read Card