50309-5 DigiSender HQ2 MODEL: DG258 ® Twin Input 5.
DG258 - DigiSender® HQ2 - Twin Input 5.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Introduction Congratulations on purchasing the DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender. This product represents state of the art wireless audio and video technology and the most advanced Infra-Red relay technology at exceptional value for money. You can now enjoy DVD quality video and Hi-Fi stereo sound from your Satellite, Cable, Freeview, DVD or VCR in another room in your home.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender STEP 1 - Unpack your DigiSender® HQ2 DigiConnector™ 2 Input 2 Input 1 DigiConnector™ 1 POWER All DigiSender® orders are computer weight checked when packed. However, it is a good idea to check all kit contents are present before proceeding with the installation.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender STEP 2 - Install the DigiSender® HQ2 Transmitter The DG258 Transmitter will send the audio and video from two connected sources (your Satellite receiver and DVD Player for example) to the DG258 Receiver, located in another room in your home. 1. 2. Connect DigiConnector™ 1 to your Satellite, Cable or Freeview box. Use the SCART socket labelled ‘TV’ or ‘OUT’. Connect any existing SCART lead into the rear of the DigiConnector™.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender continued... Note: Try to avoid positioning the DG258 Transmitter directly on top of other electrical devices as this could lead to a poor picture. 5. 6. Connect the Power Supply Unit (PSU) to the socket labelled ‘PSU’ on the rear of the DG258 Transmitter. Connect the Power Supply Unit (PSU) to an available mains socket. What’s the A/B switch for?? The Contrast (A/B) switch is present to compensate for differences in equipment set-ups.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender STEP 3 - Install the IR Systeme Technik™ Once set up correctly, the IR Systeme Technik™ will enable you to control your source equipment from the receiving location in your home. Because everyone’s set up is different there are many ways you can install the IR Systeme Technik™ and the various included accessories will help you in setting it up correctly.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender STEP 4 - Install the DigiSender® HQ2 Receiver The DG258 Receiver will pick up the signals being sent by your DG258 Transmitter and output them to a connected TV. 1. 2. Locate a vacant SCART socket on the back of your receiving TV and insert the DigiSender® SCART cable. Ensure that the Audio/Video and Remote Relay Channel switches on the back of the DG258 Receiver are set to 1. 3. 4.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender STEP 5 - Using the DigiSender® HQ2 1. 2. Switch on the source equipment (Satellite, Freeview, DVD, VCR, etc.). Turn on the DG258 Transmitter and Receiver by pushing the Power button on the front of the units. The Power button will light up blue to indicate the unit is switched on. Alternatively press the Power button on the DigiSender® Remote Control. 3.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Using the DigiSender® HQ2 The DigiSender® Remote Control 1. POWER The POWER button will turn your DigiSender® HQ2 Transmitter or Receiver On or Off. 2. Input 1 The Input 1 button will select Input 1 on the Transmitter and Receiver. Input 1 will be what ever source equipment is connected to DigiConnector™ 1. For example, your Satellite, Cable or Freeview box. 2. Input 2 The Input 2 button will select Input 2 on the Transmitter and Receiver.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Using the DigiSender® HQ2 Basic Functions Turning the DigiSender® HQ2 On and Off To turn the DigiSender® HQ2 On, press the power button on the front of the Transmitter and Receiver. The power button will light up blue to indicate that the unit is switched on. To turn the DigiSender® HQ2 Off, press and hold the power button on the front of the Transmitter and Receiver for approximately 3 seconds.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Using the DigiSender® HQ2 Advanced Functions Changing the Audio/Video Channel The DigiSender® HQ2 features 4 Audio/Video Channels. Each of these Audio/Video Channels slightly changes the frequency on which the DigiSender® HQ2 operates. Because the Audio/Video Channel switch allows you to ‘fine tune’ the frequency on which your DigiSender® HQ2 operates, it is possible to overcome most interference and reception troubles that may occur.
DG258 - DigiSender® HQ2 - Twin Input 5.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Troubleshooting Picture Problems Q: What do you see on your second television? The picture is present but poor quality POOR RANGE 1. The picture & sound quality is affected by the Transmitter and Receiver’s location. Try positioning them in different locations. The Transmitter and Receiver should be connected to a mains extension lead that can be moved. 2.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender cont... I see a snowstorm effect or plain blue screen Switch OFF your DigiSender® RECEIVER. Q: What do you now see at the second TV? I now see a Black screen I still see a snowstorm or blue picture NOT RECEIVING SIGNAL WRONG TV CHANNEL SELECTED 1. Switch the DigiSender® Receiver back on. 2. Ensure the DigiSender® Transmitter is switched on. 3.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Troubleshooting Audio Problems I can see the picture but can’t hear anything. The sound is distorted. Q: What seems to be the problem with the sound? There is a buzzing sound present. It seems to get worse during on-screen menus or bright pictures. There is a hissing sound and the volume must be turned up high on the second TV to hear anything. Page 16 1. Disconnect both the Transmitter AND Receiver SCART cables.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Troubleshooting Problems Controlling the Source Equipment If you have any difficulty operating your source equipment remote control in your second room please follow the advice below below: 1) Ensure the IR Emitter is connected to the socket labelled ‘IR’ on the DG258 Transmitter. 2) Ensure you are using the correct remote control in the second room.
DG258 - DigiSender® HQ2 - Twin Input 5.8GHz Wireless AV Sender Technical Support AEI Security & Communications Ltd is dedicated to providing our customers with first class customer care and technical support. During busy periods we would suggest using the web option to obtain support. 1. On the web... Free technical advice is available online 24/7 at our dedicated support web site: www.aei.eu 2. By telephone... We have a dedicated helpline, open Monday to Friday, 9AM - 5PM.
SPECIFICATIONS DG258 Transmitter : Remote Relay Receiver Audio/Video Frequency Modulation Video Input Level Colour Video Input Audio Input Level Audio Bandwidth Input Connectors Power Source 433.92MHz 5.7250GHz ~ 5.8750GHz FM 1V PP/75Ω Phase Alternate Line (PAL) 1.