Installation Manual

ManualsBrandsAEM ManualsAutomotiveAEM 22-401B Blue Short Ram Intake System

AEM Induction Systems 1 (800) 992-3000 WWW: http://www.aemintakes.com

Equipped with AEM

Dryflow™ Filter

No Oil Required!

INSTALLATION INSTRUCTIONS

PART NUMBER: 22-401

2000 HONDA Civic EX L4-1.6L C.A.R.B. E.O. # D-392-11

1994-1999 HONDA Civic EX L4-1.6L C.A.R.B. E.O. # D-392-6

1996-1997 HONDA Civic Del Sol L4-1.6L C.A.R.B. E.O. # D-392-6

1994-1995 HONDA Civic Del Sol L4-1.6L C.A.R.B. E.O. # D-392-23

1993 HONDA Civic Del Sol L4-1.6L C.A.R.B. E.O. # D-392-6

1993-1995 HONDA Civic Del Sol L4-1.5L C.A.R.B. E.O. # D-392-6

1992-1995 HONDA Civic LX L4-1.5L C.A.R.B. E.O. # D-392-6

1992-1995 HONDA Civic DX L4-1.5L C.A.R.B. E.O. # D-392-6

1992-1995 HONDA Civic DX Hatchback L4-1.5L C.A.R.B. E.O. # D-392-6

1992-1995 HONDA Civic SI L4-1.6L C.A.R.B. E.O. # D-392-6

1992-1993 HONDA Civic L4-1.6L C.A.R.B. E.O. # D-392-6

NOTE Legal in California only for racing vehicles which may never be used upon a highway.

Summary of content (5 pages)

PAGE 1
® Equipped with AEM Dryflow™ Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-401 2000 1994-1999 1996-1997 1994-1995 1993 1993-1995 1992-1995 1992-1995 1992-1995 1992-1995 1992-1993 HONDA HONDA HONDA HONDA HONDA HONDA HONDA HONDA HONDA HONDA HONDA Civic EX Civic EX Civic Del Sol Civic Del Sol Civic Del Sol Civic Del Sol Civic LX Civic DX Civic DX Hatchback Civic SI Civic L4-1.6L L4-1.6L L4-1.6L L4-1.6L L4-1.6L L4-1.5L L4-1.5L L4-1.5L L4-1.5L L4-1.6L L4-1.6L C.A.R.B. E.O. # D-392-11 C.
PAGE 2
PARTS LIST Description Qty. Part Number Air Filter Assy. 2.50 X 5" Dry Ele. 1 21-201DK Short Pipe 1 2-4011 Hose, Silicone 2.50x2" Black 1 5-252 Mount, Rubber 1" X 6mm 1 1228599 Grommet, 3/8" 1 784633 Grommet, 1/2" 1 784634 Vacuum Cap, 3/8" 1 8-101 Plug, Plastic 5/8" 1 8-102 Hose; 3/8"ID X 2"L 1 5-1002 Washer, 6mm Soft Mount 1 559999 Nut, M6 Hex Serrated 1 444.460.04 Hose Clamp, 3/4" 2 4093-5 1/2' Bnd. Hose Clamp, 2.15-3.00" 2 9440 1/2" Bnd. Hose Clamp, 2.31-3.
PAGE 3
Read and understand these instructions BEFORE attempting to install this product. Failure to follow installation instructions and not using the provided hardware may damage the intake tube, throttle body and engine. 1. Preparing Vehicle a. b. c. d. e. Make sure vehicle is parked on level surface. Set parking brake. If engine has run in the past two hours, let it cool down. Disconnect negative battery terminal. Do not discard stock components after removal of the factory system. 2.
PAGE 4
i. NOTE: If your application does not have a support tab then skip to step 3j. Some applications have a support tab that is welded onto the inlet pipe. i. The support tab on the inlet pipe will line up with a threaded hole on the inner fender well. Install the rubber isolator mount and attach the air inlet tube onto the rubber mount. Install the large fender washer and the lock nut onto the isolator mount stud and snug it down.
PAGE 5
d. Reconnect negative battery terminals and start engine. Let the vehicle idle for 3 minutes. Perform a final inspection before driving the vehicle. 5. CARB Sticker Placement a. The C.A.R.B. exemption sticker, (attached), must be visible under the hood so that an emissions inspector can see it when the vehicle is required to be tested for emissions. California requires testing every two years, other states may vary. 6. Service and Maintenance ® a.