Installation Manual

ManualsBrandsAEM ManualsAutomotiveAEM 22-413B Blue Short Ram Intake System

AEM Induction Systems 1 (800) 992-3000 WWW: http://www.aemintakes.com

Equipped with AEM

Dryflow™ Filter

No Oil Required!

INSTALLATION INSTRUCTIONS

PART NUMBER: 22-413

1996-2000 HONDA Civic CX L4-1.6L C.A.R.B. E.O. # D-670

1996-2000 HONDA Civic DX L4-1.6L C.A.R.B. E.O. # D-670

1996-2000 HONDA Civic LX L4-1.6L C.A.R.B. E.O. # D-670

NOTE: Legal in California only for racing vehicles which may never be used upon a highway

Summary of content (5 pages)

PAGE 1
® Equipped with AEM Dryflow™ Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-413 1996-2000 1996-2000 1996-2000 HONDA Civic HONDA Civic HONDA Civic CX DX LX L4-1.6L L4-1.6L L4-1.6L C.A.R.B. E.O. # D-670 C.A.R.B. E.O. # D-670 C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles which may never be used upon a highway AEM Induction Systems 1 (800) 992-3000 WWW: http://www.aemintakes.
PAGE 2
PARTS LIST Description Qty. Part Number Air Filter Assy. 2.50 X 5" Dry Ele. 1 21-201DK Short Pipe 1 2-4131 Hose, Silicone 2.50x3" Blk. 1 5-250 Mount, Rubber 1" X 6mm 1 1228599 Grommet, 3/8" 1 784633 Grommet, 1/2" 1 784634 Hose; 1/2"ID X 7"L 1 5-5007 Washer, 6mm Soft Mount 1 559999 Nut, M6 Hex Serrated 1 444.460.04 Hose Clamp, 3/4" 2 4093-5 1/2' Bnd. Hose Clamp, 2.15-3.00" 2 9440 1/2" Bnd. Hose Clamp, 2.31-3.25" 1 9444 Hose Clamp, 1" 2 99024.
PAGE 3
Read and understand these instructions BEFORE attempting to install this product. Failure to follow installation instructions and not using the provided hardware may damage the intake tube, throttle body and engine. 1. Preparing Vehicle a. b. c. d. e. Make sure vehicle is parked on level surface. Set parking brake. If engine has run in the past two hours, let it cool down. Disconnect negative battery terminal. Do not discard stock components after removal of the factory system. 2.
PAGE 4
h. Install the air filter. ® i. Install the AEM filter onto the end of the inlet tube. Push the filter on around 2 inches over the inlet pipe and install one hose clamp to secure the filter on to the inlet pipe. Once fitment is checked, you can either push the filter on to the inlet pipe more or less depending on clearances. Tighten the hose clamp after this is done. Be sure to leave ample clearance between the filter and any surrounding components. i.
PAGE 5
For technical inquiries e-mail us at sales@aemintakes.com or call us at 800.992.3000 AEM Air Intake System Warranty Policy ® AEM warrants that its intake systems will last for the life of your vehicle. AEM will not honor this warranty due to mechanical damage (i.e. improper installation or fitment), damage from misuse, accidents or flying debris. AEM will not warrant its powder coating if the finish has been cleaned with a hydrocarbon-based solvent.