User's Manual
View the expanded manual:
http://aeotec.com/support
Aeotec by Aeon Labs RGB Bulb.
Aeotec RGB Bulb is a low-cost Z-Wave LED module which
allows control (on/off/dim) with the use of Z-Wave.
It’s a bulb has a Smart RGB LED, which can be used to add
colour to your home. The bulb has 5 main colour channels
available for you to adjust: Red, Green, Blue, Warm White
and Cold White. You can congure its colour according to your
favour.
The RGB Bulb is also a security Z-wave device and supports
the Over The Air (OTA) feature for the product’s firmware
upgrade.
Getting your RGB Bulb up and running is as simple as
plugging it into a wall socket and linking it to your existing
Z-Wave network. The following instructions tell you how to
link your RGB Bulb to your Z-Wave network using an Aeotec
by Aeon Labs’ Z-Stick or Minimote controller. If you are using
other products as your main Z-Wave controller, such as a
Z-Wave gateway, please refer to the part of their respective
section of their instruction manual that tell you how add new
devices to your network.
If you’re using a Z-Stick: If you’re using a Minimote:
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
Decide on where you want your RGB Bulb to be placed and
plug it in to a wall outlet. Its RGB LED will be active with a
colourful gradient.
If your Z-Stick is plugged into a gateway or a computer,
unplug it.
Take your Z-Stick to your RGB Bulb.
Press the Action Button on your Z-Stick.
Press the external switch of RGB Bulb to turn it off and then
press the external switch again to turn it on.
If RGB Bulb has been successfully linked to your Z-Wave
network, its warm white LED will be solid. If the linking was
unsuccessful, the RGB Bulb will continue to be active with
a colourful gradient.
Press the Action Button on the Z-Stick to take it out of
installation mode and return it to your gateway or computer.
Decide on where you want your RGB Bulb to be placed
and plug it in to a wall socket. Its RGB LED will be active
with a colourful gradient.
Take your Minimote to your RGB Bulb.
Press the Include button on your Minimote.
Press the external switch of RGB Bulb to turn it off and then
press the external switch again to turn it on.
If RGB Bulb has been successfully linked to your Z-Wave
network, its warm white LED will be solid. If the linking was
unsuccessful, and the RGB Bulb will continue to be active
with a colourful gradient.
Press any button on your Minimote to take it out of
installation mode.
®
Familiarize yourself with your RGB Bulb.
Quick start.
With your RGB Bulb now working as a part of your smart
home, you’ll be able to configure it to indicate different
colours from your home control software via setting the RGB
value. Please refer to your software’s user guide for precise
instructions on conguring your RGB Bulb to your needs.
You’re able to change your RGB Bulbs colour manually. After
the RGB Bulb is included into your network, switching the
RGB Bulb on and off 2 times within 2 seconds via external
switch will change the colour to the next (Warm white, Cold
white, Red, Green or Blue).
Your RGB Bulb can be removed from your Z-Wave network
at any time. You’ll need to use your Z-Wave network’s main
controller, and to do this, and the following instructions will tell
you how using the Aeotec by Aeon Labs’ Z-Stick or Minimote
controller. If you are using other products as your main Z-Wave
controller, please refer to the part of their respective manuals
that tells you how remove devices from your network.
Removing your RGB Bulb from a Z-Wave network.
If you’re using a Z-Stick:
1.
2.
3.
4.
5.
6.
If your Z-Stick is plugged into a gateway or a computer,
unplug it.
Take your Z-Stick to your RGB Bulb.
Press the Action Button on your Z-Stick.
Press the external switch of RGB Bulb to turn off and then
press the external switch again to turn on it, repeat the
operation 3 times within 2 seconds.
If your RGB Bulb has been successfully removed from
your network, Its RGB LED will be active with a colourful
gradient. If the removal was unsuccessful, the RGB LED
will be solid.
Press the Action Button on the Z-Stick to take it out of
removal mode.
If you’re using a Minimote:
1.
2.
3.
4.
5.
Take your Minimote to your RGB Bulb.
Press the Remove Button on your Minimote.
Press the external switch of RGB Bulb to turn off and then
press the external switch again to turn on it, repeat the
operation 3 times within 2 seconds.
If your RGB Bulb has been successfully removed from
your network, Its RGB LED will be active with a colourful
gradient. If the removal was unsuccessful, the RGB LED
will be solid.
Press any button on your Minimote to take it out of removal
mode.
Technical specications.
External
Switch
Bulb , LED Bulb