Fantem In-wall Dimmer Nano Dimmer View the expanded manual: http://aeotec.com/support IMPORTANT! This product has been fully tested and certified to work with Z-Wave by the Z-Wave Alliance. It is crafted using Z-Wave Plus, the latest device version of Z-Wave. As such, if the product does not work with your gateway, please be sure to check with your gateway manufacturer that they have integrated this device with their gateway for full operation.
1 Warning Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. Certifications (regional): Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countries FCC ID: XBAFT111 Aeotec by Aeon Labs Nano Dimmer.
2 Familiarize yourself with your Nano Dimmer. RF antenna Touch panel connection port RGB LED Fastening screws Action Button to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consul the dealer or an experienced radio/TV technician for help. UL NOTICE (For USA/Canada).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Install the Nano Dimmer. Important: A licensed electrician with knowledge and understanding electrician systems and electrical safety should complete the electrical installation. 1. Shut off the main circuit breaker of your home for safety during the installation and ensure the wires are not short circuited during the installation which will cause damage to the Nano Dimmer. WITHIN THIRTY (30) DAYS FROM AEON LABS' DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY.
DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BYCUSTOMER, COMPANY OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR TORT, OR OTHERWISE EVENIF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Wiring diagram of 3-Wire system. L N OUT COM S1 S2 Touch panel Live Neutral Wiring diagram of 2-Wire system.
damage, negligence, electrical power problems, or modification to the Products or its components. Aeon Labs does not authorize any person or party to assume or create for it any other obligation or liability in connection with the Products except as set forth herein. Aeon Labs will pass on to Company all manufacturers’ Material warranties to the extent that they are transferable, but will not independently warrant any Material.
bypass can be added to act as a dummy load to keep your Nano Dimmer get enough power from the power supply. It can also keep your light from flickering when diming off the light. L N OUT COM S1 S2 Touch panel Bypass Live Neutral 8 and the operating manual supplied. Warranty claims must be made to the Company who you have purchased from in writing within thirty (30) days of the manifestation of a problem.
subsequent to your products’ warranty, please get in touch with our support team via http://aeotec.com/ support. The Company you bought this product from has also guaranteed to assist you with any of your support needs, and you can also contact them for accordingly. This guarantee made by the company who you purchased the product from includes the transfer of Aeon Labs’ full warranty to that Company.
The below diagram will show you that the Nano Dimmer uses the SPDT (Single-Pole Double-Throw) switches as the external manual switch. Wiring diagram of SPDT as the external manual switch. L N OUT COM S1 S2 Control ability Touch panel 3-Way Switch (SPDT) 3-Way Switch (SPDT) Live Neutral Since the S1 port and S2 port can be used to control the load separately, you can choose to connect the SPDT switches to the S1 or S2. 10 Model number: FT111-A/ZW111-A Power input: AC 120V, 60Hz. Rated output: Max 1.
mode. 2. Press the Action Button 2 times within 1 second on the Nano Dimmer, the blue LED (secure indication) will blink to indicate the Nano Dimmer is entering into secure pairing mode. 3. If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colourful gradient, repeat the instructions above from step 1. Reset your Nano Dimmer.
Note: The above physical connection diagram is for 3-Wire system, the below diagram would be for the 2-Wire system. L N L N OUT COM S1 S2 In 2-Wire system, since the power input terminals of Nano Dimmer just need to connect one power wire, so the terminal of “N” on Nano Dimmer should connect to the “L” on the Nano Dimmer. 4. Mounting the gang box. a. Position all wires to provide room for the device. Place the Nano Dimmer inside the gang box towards the back of the box. b.
panel. When you have already connected it to the Nano Dimmer, you will be possible to control the Nano Dimmer through the Touch panel directly. box, away from all other wiring. c. Reinstall the Nano Dimmer to the gang box. d. Reinstall the cover onto the gang box. N L 1 Monitoring Energy Consumption. The Aeotec Nano Dimmer can report wattage energy usage or kWh energy usage to a Z-Wave control point when requested.
Note: 1). The gang box should be sized 3×2×2.75 inch/ 75×50×70 mm or larger, minimum volume 14 in3 / 230cm3. 2). Use flexible copper conductors only. 3). If a Bypass installation is needed, the Bypass should be in parallel with the bulb load, see below: Bypass Warning: The main circuit breaker or fuse must be shut off during the Bypass installation or bulb change. 5. Restore Power. Restore power at the main circuit breaker or fuse.
Your Nano Dimmer can be removed from your Z-Wave network at any time. You’ll need to use your Z-Wave network’s main controller. To set your Z-Wave controller/gateway into removal mode, please refer to the respective section within your controller instruction manual. 1. Set your Z-Wave controller into removal mode. 2. Press the Action Button on the Nano Dimmer or toggle the external manual switch 2 times in fast succession. 3.
Dimmer to turn it On/Off/Dim directly via pressing your Nano Dimmer’s Action Button, it is time to add your Nano Dimmer to the Z-Wave network. To set your Z-Wave gateway/controller into pairing mode, please refer to the respective section within your controller instruction manual. 1. Set your Z-Wave controller into pairing mode. 2.
FCC Part 15.19 Warning Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE.
