User Manual

ManualsBrandsAeon Labs ManualsElectronicsWater Sensor 6 with Water Sensor 6 Dock

ZW122-A User Manual

Page 1

Water Sensor 6

[Line art drawing of Water Sensor 6 ]

Next Section

[Heading 1]FANTEM by Aeon Labs Water Sensor 6 [/Heading 1]

FANTEM by Aeon Labs Water Sensor 6 brings intelligence to a new level, one that is suited to

both safety

and convenience. It contains 4 sensor probes, which would be more accurately to

detect the presence and absence of water or detect whether there is water leak in some places

of your home. The Water Sensor 6 has an inbuilt buzzer that can play alarm sounds to let you

know when the water is detected.

The Water Sensor 6 is also a security Z-Wave device that supports Over The Air (OTA)

for firmware updates.

Next Section

[Heading 1 ]Familiarize yourself with your Water Sensor 6.[/Heading

1] Package

contents:

1. Main sensor unit (×1).

2. CR123A battery (×1).

3. Screw (×2).

Summary of content (9 pages)

PAGE 1
ZW122-A User Manual Page 1 Water Sensor 6 [Line art drawing of Water Sensor 6 ] Next Section [Heading 1]FANTEM by Aeon Labs Water Sensor 6 [/Heading 1] FANTEM by Aeon Labs Water Sensor 6 brings intelligence to a new level, one that is suited to both safety and convenience. It contains 4 sensor probes, which would be more accurately to detect the presence and absence of water or detect whether there is water leak in some places of your home.
PAGE 2
Next Section [Heading 1]Quick Start.[/Heading 2] [Heading 2]Power on your Sensor.[/Heading 2] 1. Remove the clear battery insulator by pulling it away from the Water Sensor 6. Now, you can try pressing the Sensor’s Action Button, if you can see the RGB LED blinks, which indicates that the Sensor is powered on. 2. Secure the Sensor plate using the screws provided.
PAGE 3
After complete the securing of the Sensor plate, your Water Sensor 6 unit will possess the high waterproof level of IP65. Your Water Sensor 6 also can be powered by the Dock, if you want to know more about it, please refer to the Dock manual. [Heading 2] Adding your Sensor to your Z-Wave network.[/Heading 2] With your sensor is powered on, it’s time to add it to your Z-Wave network. 1. Let your Z-Wave primary controller/gateway enter into adding/inclusion mode. 2.
PAGE 4
If you want to detect whether or not there would be water leakage from the fridge, you can put the Water Senor near to the fridge. Just note that the Water Sensor cannot be put inside the fridge or other metal container, since the metal container will affect the signal strength of the Sensor unit and your main controller. [Heading 2]Some conditions of the water can be detected by the Sensor.[/Heading 2] The Water Sensor 6 will be triggered when the water leak happens in below situations: 1.
PAGE 5
4. Water is detected by the Sensor’s probe 3 and 4 5. Water is detected by the Sensor’s probe 1,2,3 and 4 Next Section [Heading 1]Advanced.[/Heading 1] [Heading 2]Send a wake up notification.[/Heading 2] In order to send your Sensor new configuration commands from your Z-Wave controller or gateway, it will need to be woken up. 1. Press the Action Button on the Sensor unit and then release the Action Button. This will trigger and send a wake up notification command to your controller/gateway. 2.
PAGE 6
1. 2. 3. 4. Turn your primary controller into device removal mode. Take the Sensor unit near to your primary controller. Press the Action Button on your Sensor. If your Water Sensor 6 is successfully removed from the Z-Wave network, the RGB LED will become a colourful gradient for a few seconds and then turn off. If the removing was unsuccessful, the blue LED will be solid for 2 seconds and then turn off, repeat the above steps.
PAGE 7
2. Separate the battery cover from the Sensor unit. If you have a hard plastic board( about 0.8 to 1.0mm thickness) on hand, you can use it to separate the battery cover directly: Push or move the plastic board along the gap between battery cover and Sensor unit, refer to the direction of arrows, see the figure below: You can also open the battery cover through your fingers if you are confident about this way. Find the position of the screw side, see the operating steps below: a.
PAGE 8
Next Section [heading 1]Technical specifications. [/heading 1] Model number: FT122-A. Power supply: CR123A lithium battery, 3V, 1500mAh. Operating temperature: 0°C to 40°C. Storage temperature: -20°C to 60°C. Water proofing: IP65. Max volume of buzzer: 60dB at 2 meters away. Operating distance: Up to 100 feet/30 metres indoors or 492 feet/150 metres outdoors. Next Section [heading 1]Warranty.[/heading 1] [As is defined for the whole company] Next Section [heading 1]Certifications.
PAGE 9
FCC Part 15.19 Warning Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE.