User's Manual
MOTE.
Oomi MOTE is an intelligent Z-Wave® remote controller that mounted
on a wall. It has 4 touch buttons that you can easily control the Z-Wave
devices in your home network via touching, long pressing or sliding
the button areas.
Its surface has a RGB LED to indicate the button actions also
accompanied by touch beep and vibration.
The MOTE is also a security Z-Wave device and supports Over The
Air (OTA) feature for the products rmware upgrade.
Familiarize yourself with your MOTE.
Quick start.
Advanced.
1.
2.
Installing your MOTE.
Adding your MOTE to your Z-Wave network.
Attach your MOTE to its Back Mounting plate.
Send a wake up notification.
Removing your MOTE from a Z-Wave network.
Security or Non-security feature of your MOTE in Z-wave network.
Advanced Parameter Configurations.
1.
2.
Let your Z-Wave primary controller/gateway enter into pairing/
inclusion mode.
Take your MOTE near to your primary controller.
With your MOTE added to the Z-Wave network. It’s now time to insert
the main unit into the corresponding Back Mount plate.
Put the main unit in the top-left direction on the Back Mounting, and
then push the MOTE into the Back Mounting Plate, the MOTE will
be attracted by the magnets on the Back Mount plate, as the gure
below shows.
With your MOTE now working as a part of your smart home, you’ll
be able to configure it from your home control software or phone
application. Please refer to your software’s user guide for precise
instructions on conguring the MOTE to your needs.
With your mounting plates prepared to hold each component of your
MOTE, it’s time to add it to your Z-Wave network.
In order to send your MOTE new conguration commands from your
Z-Wave controller or gateway, it will need to be woken up.
Remove your MOTE unit from its Back Mounting Plate, press and
hold the Action Button for 3 seconds(the buzzer chirp once and
the orange LED will be ON) on the back of the MOTE unit and then
release it. This will trigger and send a wake up notication command
to your controller/gateway, then your MOTE will wake up for 10
minutes and the orange LED will fast blink while it is awake (if the
MOTE does not receive the Wake Up No More Info from the primary
Controller).
Your MOTE can be removed from your Z-Wave network at any time.
You'll need to use your Z-Wave network's main controller/gateway.
To do this, please refer to the part of their respective manuals that tell
you how to remove devices from your network.
1.
2.
3.
4.
Put your primary controller into device removal mode.
Unlock your MOTE from the Back Mount plate and take the MOTE
unit near to your primary controller.
Press the Action Button on your MOTE.
If your MOTE is successfully removed from the Z-Wave network,
the LED will become a colourful gradient for a few seconds and
then turn off. If the removing was unsuccessful, the red LED will be
solid for 2 seconds and then turn off, repeat the above steps.
Not all gateways will allow you to further configure your Z-Wave
devices, but in the case that your gateway does allow it, the MOTE
Touch beep
This will enable or disable the sound effects when you press or touch
the sensing area. By default, this is enabled.
Parameter 1 [1 byte]
0: Disable
1: Enable
Note: You can also enable or disable the sound effects via pressing
and holding the Action Button for 12 seconds (the buzzer chirp once
and the red LED will fast blink) and then release.
Touch vibration
This will enable or disable the vibration effects when you press or
touch the sensing area. By default, this is enabled.
Parameter 2 [1 byte]
0: Disable
1: Enable
Note: You can also enable or disable the vibration effects via pressing
and holding the Action Button for 17 seconds (the buzzer chirp once
and the red LED will be solid) and then release.
Including MOTE as a non-secure device:
If you want your MOTE as a non-security device in your Z-wave
network, you just need to press the Action Button once on MOTE
when you use a controller/gateway to add/include it. The green LED
will be on for 2 seconds and then the orange LED will fast blink for
10 minutes (if the MOTE does not receive the Wake Up No More
Info command from primary Controller) to indicate the inclusion is
successful.
Including MOTE as a secure device:
In order to take full advantage of all functionality the MOTE, you may
want your MOTE is a security device that uses secure/encrypted
message to communicate in Z-wave network, so a security enabled
controller/gateway is needed for the MOTE to be used as a security
device. You need to press the MOTE’s Action Button 2 times within
1 second when your security controller/gateway starts the network
inclusion. The blue LED will be on for 2 seconds and then the orange
LED will fast blink for 10 minutes (if the MOTE does not receive the
Wake Up No More Info command from primary Controller) to indicate
the inclusion is successful.
Selecting a place or wall in your home to afx your MOTE’s Back
Mount plate.
Using the Double-sided tap, wipe the two surfaces clean of any oil
or dust with a damp towel. When the surface has completely dried,
peel one side of the tape back and attach it to the corresponding
section on the rear side of the Back Mounting Plate.
Advanced functions.
MOTE
1
2
3
4
5
1.
2.
3.
4.
MOTE
Back-Mount plate
Double-Sided tape
Micro USB cable
① ②
③
④
RGB LED
Button 1
Button 3
Button 2
Button 4
Mangent
Mangent
Micro USB port
Action Button
Main unit (Front)
Main unit (Back)
Back-Mount plate
Mangent
Note: When the MOTE is placed on somewhere, keep the glass
button surface upward direction and no other physical surface or
desktop contact with the glass button surface to avoid false triggering
and battery consumption.
Press the Action Button once on your MOTE, the LED will blink with
green color.
If your MOTE has been successfully added to your Z-Wave
network, its green LED will be solid for 2 seconds and then off. If
the adding was unsuccessful and the red LED will be solid for 2
seconds and then off, repeat the above steps.
3.
4.
has some available parameter configurations that will allow you to
congure it further to your liking.
NFC
F
T130-A