Installation Guide

ManualsBrandsAero Pure ManualsBathQuiet Adjustable Speed 50-110 CFM Bathroom Exhaust Fan with Humidity Sensor & LED Light Ceiling Mount ENERGY STAR White

BATH FAN

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

..............................................................................................................

.......................................................................................

..........................................................................................................

........................................................................

............................................................................................................

...................................................................................................

..................................................................................................................

...........................................

.............................................................

.................................................................................

...................................................................................

...................................................................

......................................................................................................

...............................................................................................................

TABLE OF CONTENTS

UNPACKING

SUPPLIED ACCESSORIES

DESCRIPTION

GENERAL SAFETY INFORMATION

DIMENSIONS

WIRING DIAGRAM

FEATURES

INDICATION (PLUG-IN DEVICES)

INSTALLATION

I (NEW CONSTRUCTION）

INSTALLATION

II (RETROFIT)

MAINTENANCE (CLEANING)

PRACTICAL GUIDE TO INSTALLATION

SPECIFICATIONS

WARRANTY

Thank you very much for purchasing our bath fan.

Please read the instructions carefully before attempting to install,

operate or service our ventilating fan. Failure to comply

with instructions could result in personal injury or property

damage. Please retain this booklet for future reference.

Model No.

ABF110DHL5 Series

ABF110DHG5 Series

ABF110DCMH-SG5

ABF110DHL6 Series

ABF110DHG6 Series

ABF110DCMH-SG6

ABF110DHL1 Series

ABF110DHG1 Series

Summary of content (15 pages)

PAGE 1
BATH FAN Model No. INSTALLATION INSTRUCTIONS ABF110DHG5 Series ABF110DHL5 Series ABF110DCMH-SG5 ABF110DHG6 Series ABF110DHL6 Series ABF110DCMH-SG6 ABF110DHG1 Series ABF110DHL1 Series READ AND SAVE THESE INSTRUCTIONS Thank you very much for purchasing our bath fan. Please read the instructions carefully before attempting to install, operate or service our ventilating fan. Failure to comply with instructions could result in personal injury or property damage.
PAGE 2
UNPACKING Unpack and carefully remove the unit from carton. Refer to the supplied accessories list to verify that all parts are present. SUPPLIED ACCESSORIES or Grille or ABF110DHG5 ABF110DHG6 or or ABF110DHL5 or ABF110DCMH-SG5 ABF110DCMH-SG6 1 ABF110DHL6 or ABF110DHG1 ABF110DHL1 Suspension bracket assembly 1 Long screw (ST4X30) 5 Wire Protector Nut 1 Installation instructions 1 DESCRIPTION These bath fan models are listed by ETL under ETL file No.5011292.
PAGE 3
GENERAL SAFETY INFORMATION 1. Do not install this ventilating fan where interior room temperature may exceed 104°F (40°C). 2. Make sure that the electric service supply voltage is AC 120V, 60Hz. 3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC), and the Occupation Safety and Health Act (OSHA). 4. Always disconnect the power source before working on or near the fan, motor, light fixture, or junction box. 5.
PAGE 4
DIMENSIONS Model: ABF110DHG6 Series, ABF110DHL6 Series, ABF110DCMH-SG6 ③ Unit: inches (mm) 5 4/5 (147) ⑦ 4 7/8 (123) 3 7/8 (98) 3 4/5 (97) ② 7 1/3 (186) 10 2/5 (265) ⑪ ⑥ ④ ⑨ ① 13 (330) 3/5 (14.5) ⑩ 10 1/4 (260) 12 1/8 (308) ⑧ ⑤ Model: ABF110DHG5 Series, ABF110DHL5 Series, ABF110DCMH-SG5 ③ ⑦ ② 5 4/5 (147) 4 7/8 (123) 3 4/5 (97) 3 7/8 (98) ④ ⑥ ① ⑩ 10 1/4 (260) ⑤ ⑧ 3/5 (14.
PAGE 5
WIRING DIAGRAM Model: ABF110DHG5 / ABF110DHG6 / ABF110DHG1 ABF11DCMH-SG5 / ABF110DCMH-SG6 Fan body Junction box P C B Motor Yellowgreen White Neutral Red Signal Red Black Signal Green Ground Control switch Model: ABF110DHL5 / ABF110DHL6 / AB110DHL1 Fan body Motor P C B Yellowgreen Junction box White Neutral Red Signal Red Black Signal Green Ground Control switch Live Power switch Live Power switch Light Body Brown Live (Light) White Neutral Blue Live(N.
PAGE 6
PLUG-IN DEVICES Humidity(RH%) 30 80 Humidity Sensor Module- Included in this Aero Pure fan. Insert module into USB interface. The fan automatically turns on or boosts to a higher speed when the Relative Humidity (RH) exceeds the user-adjustable set-point. The fan automatically runs in a lower speed after a period of time delay or stops running when the Relative Humidity falls below the set-point. Humidity detection value setting range: 30% - 80% Motion Sensor Module- Insert model into USB interface.
PAGE 7
INSTALLATION I (NEW CONSTRUCTION) ！ CAUTION: Please wear gloves during the installation work. IMPORTANT: Remove the tape from damper and adaptor before installation. As shown below: 4 Screws (ST4x30) Joist situation: Fig.1 L Two cases of spacing L : A 12 inches (305 mm) B 16~24 inches (406~610 mm) A If the spacing L is 12 inches (305 mm) on joists, please follow the installation step as (Fig.1). Secure 4 screws (ST4X30) at flange of frame to the joists.
PAGE 8
INSTALLATION I (NEW CONSTRUCTION) CONTINUED 1. Bend down 8 tabs for positioning as (Fig.2.a) and unfold the bracket assembly as (Fig.2.b). 2. Fix one side of the bracket assembly to the joists by drilling 2 tapping screws (ST4x20) which have been fixed on it. (Fig.3） Unit: inches (mm) Active part Screws (ST4X20) Joist Fig.3 3. Adjust the length of bracket assembly as the spacing between joists, and install to joist by drilling the other 2 tapping screws which have been fixed on the other side.
PAGE 9
INSTALLATION I (NEW CONSTRUCTION) CONTINUED 6.Install a circular duct and secure it with clamps or ties and seal it with mastic or approved duct tape. A 4”, 5”, or 6” circular duct is needed to connect to relevant part of adaptor. (Fig.6) Circular duct Duct tape Fig.6 7.Remove the knock-out plate and secure conduit or wire protector nut to knock-out hole. (Fig.7. I) I Attach cable clamp to Knockout Plate. Knockout Plate mounts to outside of Housing and may be oriented as desired.
PAGE 10
INSTALLATION I (NEW CONSTRUCTION) CONTINUED 9.Insert mounting springs into slots and mount grille to fan body（Fig.9） Ceiling Slot Mounting spring Grille Fig.9 10.For grille with a light, refer to the following installation method. ！ CAUTION: 1.Before turning on the light, make sure the connector is at the correct position. If not, the lighting will not work. 2.The claw of connector must be secured to the rib completely. (Fig.10) Insert the grille mounting spring on the wiring side into the slot.
PAGE 11
INSTALLATION I (NEW CONSTRUCTION) CONTINUED 11.For grille with a module, refer to the following installation method. Insert the grille mounting spring on the wiring side into the slot. Insert the USB connector into the USB receptacle and insert other mounting spring into the slot as shown and mount grille to fan body. (Fig.12) Fig.12 INSTALLATION II (RETROFIT) 1.
PAGE 12
INSTALLATION II (RETROFIT) CONTINUED 2. Install a circular duct and secure with clamps or ties and seal with mastic or approved foil tape. A 4”, 5”, or 6” circular duct is needed to connect to relevant part of adaptor. (Fig.14) Unit:inches (mm) Follow step 4 of Installation I (NEW CONSTRUCTION page 8) to complete the adaptor installation. (Fig.14) Screws (ST4x30) 3. Remove the knock-out plate and secure conduit or wire protector nut to knock-out hole. (Fig.15) Refer to wiring diagram on page 5.
PAGE 13
MAINTENANCE (CLEANING) WARNING: Disconnect power source before working on unit. Routine maintenance must be done every year. CAUTION: 1. Never use gasoline, benzene, thinner or any other such chemicals for cleaning the ventilating fan. 2. Do not immerse motor in water when cleaning. 3. Do not soak resin parts in water over 140°F (60°C). Grille Fig.17 1. Remove grille. (Squeeze mounting spring and pull down carefully). (Fig.17) 2. Clean grille. (Don’t put into hot water.
PAGE 14
PRACTICAL GUIDE TO INSTALLATION Properly insulate the area around the fan to minimize building heat loss and gain. (Fig.21) 4 inches or 6 inches roof jack, wall cap, or soffit vent with backdraft damper Loose fill or batt insulation can be placed directly over the fan housing in the attic. 2-3 ft straight run before elbow The fans and fan/light combination units do not create excessive heat that is a common problem with recessed light fixtures or some competitors′ fan/light combinations.
PAGE 15
WARRANTY This warranty covers all defects in workmanship or materials for: The mechanical and electrical parts contained in this product for a period of 72 months from the date of purchase. You must keep and be able to provide your original sales receipt as proof of date of purchase. This warranty is covered to the original retail purchaser of this product only. The manufacturer will replace any mechanical or electrical part that proves defective in normal household use for a period of 72 months.