User guide

FIRMER
AUTO
INFLATE
OFF
FIRMER
AUTO
INFLATE
OFF
DEFLATION AND STORAGE
1. Open the Rapid Release valve cover and press the rubber flapper inside the valve to the locked open position to release the air (see figure D).
2. Fold sides of bed into the center along its length (see figure H). Tightly roll your bed towards the valve.
3. Roll the bed completely until all air is expelled. When the bed is completely rolled, turn valve cap clockwise until it is locked in place.
4. Slide the duffel bag over your AeroBed. Store your bed and pump until its next use.
8120 3/10
Pump 232RV Dbl Imp/RR
Combo
Instruction Manual
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Before inflation, make sure flapper inside valve is closed (see figure A). If not, pull red bar firmly to close. Then, twist valve cover securely on
(see figure B).
3. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.2A
(Note: 230VAC product sold outside of North America). This product has a polarized attachment plug (one blade is wider than the other) as a safety
feature (see figure E). This plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
4. Turn dial on pump to “auto inflate” position (see figure F). Bed will begin to inflate automatically.
P
ump will automatically shut-off once the bed is fully inflated. Time to auto stop inflation will vary according to room temperature.
5. Once bed is fully inflated and pump has shut itself off, turn dial to “off” position.
6. Lie on bed and check the firmness. If you want your bed to be softer, press the rubber flap inside the valve (see figure C).
7. If you want your bed to be FIRMER, turn the dial on pump to “firmer” position (see figure G). Once desired firmness is achieved, turn dial to
“off” position.
8. This bed is equipped with auto reset. If run continuously for more than 5 minutes, pump will reset. Unplug and shut off.
Wait 15 minutes before turning pump on to adjust firmness.
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.
Thank you for joining the AeroBed
®
family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new
AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock:
- Always unplug from outlet when not in use and before cleaning.
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Never operate the product with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- To disconnect, press control to “off” position, then remove plug.
WARNING:
Product is for indoor use only. Do not use outdoors. For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- Bed supports a maximum weight of Twin 350 lbs., Full 450 lbs., Queen 600 lbs.
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer serious
or fatal injury through suffocation, falling from or rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces.
Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near
or against heaters, open flame, or other hot objects.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time. Do not
use pump continuously for more than 5 minutes.
To avoid excessive heat build-up in the pump, let it rest for 5 minutes between complete inflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, 1-888-462-4468
for repair or servicing information.
E
F
G
H
Tap red bar gently for
desired firmness
Deflating – Push flapper
valve open into locked
position
Pull red bar firmly to close
flapper valve
Twist valve cover back on
C
A
B
D
SERVICING OF DOUBLE-INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated
product, nor is a means for grounding to be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the
system, and is to be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they
replace.