User guide

ManualsBrandsAeroBed ManualsFurniturePakmat

8111 Rev 1/10

PakMat

Instruction Manual

INFLATION

NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.

1. Remove the air bed from the pump by separating the handle portion from the pump external shell. (See figure A)

Carefully slide the bed out of the handle portion of the pump and place the unrolled bed flat on the ground or other surface

free of obstructions or sharp objects.

2. Extend the pump adapter out from the bottom of the pump housing by pulling on the slanted portion of the adapter with

two fingers, until the adapter is fully extended and locked in place. (See figure B)

3. Before inflation make sure the flapper valve inside the bed is closed. If it is not closed then pull firmly on the red bar

attached to the flapper valve to close it. Align the pump adapter up with the bed valve. Push and twist the adapter on to

the valve. You will need to turn the pump clockwise until it comes to a stop. (See figure C)

4. Now you can start inflating the bed. Just pull the handle backwards and the push forward to flow air into the bed.

(See figure D) It should be fully inflated and firm in about 90 seconds.

A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.

Thank you for joining the AeroBed

family by purchasing one of our products. This new innovative air bed requires no batteries or external power source of any kind to

operate. The airbed itself is made with the most durable, eco-friendly materials available in the marketplace today. The product itself is lightweight and compact, but still

provides all the comfort you have come to expect from an AeroBed. The unique horizontal channel construction provides a truly comfortable night’s sleep whether in your

own backyard or hiking in the mountains.

IMPORTANT SAFETY INFORMATION AND WARNINGS

SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

IMPORTANT:

Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.

WARNING: Never drop or insert any object into any open bed valve.

WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.

ADDITIONAL WARNINGS:

- Bed supports a maximum weight of 350 lbs.

- This is not a water toy. Use as a mattress only.

- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer

serious or fatal injury through suffocation, falling from or rolling off the bed, or becoming trapped.

- Use on flat surfaces only. Bed may tip over on uneven surfaces.

- Inflate bed fully. Partially inflated mattresses can cause suffocation.

- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near

pointed/sharp items or surfaces. Bed may puncture.

- Do not step or jump on bed or use as a trampoline.

- This bed is made of polyester and TPU and therefore may melt or burn if it comes in contact with any flame or heat

source. Do not place it near or against heaters, open flame, or other hot objects.

- Do not attempt to repair or service the pump. Contact Aero Products International, Inc. at 1834 Walden Office Square,

Third Floor, Schaumburg, IL 60173, 1-888-462-4468 for repair or servicing information.

DEFLATION AND STORAGE

1. Open the rapid release valve cover and push the rubber flapper inside the valve to the lock open position to release the air.

2. Let all the air out of the bed until it is completely flat (See figure E)

3. Lay the bed out flat and fold in the sides of the bed along the entire length in half. (See figure F)

4. Roll the bed up tightly in the direction of the valve to expel any trapped air. (See figure G)

5. When the bed is completely rolled up tightly make sure you close the flapper valve by pushing on the red bar firmly and

twist the cap back on the valve.

6. Make sure that you slide the Pakmat bed back into the handle portion of the pump and not outer shell or it will not close

correctly. (See figure H)

7. Once the bed is stored neatly back in the pump, make sure you store the entire product in a clean dry place at room

temperature (above 50

F/ 110

C). Storing your air bed under 50

F (10

C) or above 100

F (38

C) may affect the

performance of this product and will not be covered under warranty.

Summary of content (2 pages)

PAGE 1
8111 Rev 1/10 PakMat Instruction Manual Thank you for joining the AeroBed® family by purchasing one of our products. This new innovative air bed requires no batteries or external power source of any kind to operate. The airbed itself is made with the most durable, eco-friendly materials available in the marketplace today. The product itself is lightweight and compact, but still provides all the comfort you have come to expect from an AeroBed.
PAGE 2
CARE AND MAINTENANCE 1. Inspect your bed prior to each use. 2. Keep your bed away from any sharp objects or obstacles with rough edges. Large cuts or snags may not be repairable and will not be covered by your bed warranty. 3. We recommend that you do not let the surface of your AeroBed® get wet. Repeated exposure to water or other liquids may cause damage to the plush surface that will not be covered by your warranty.