User guide

Thank you for joining the Aero
®
Sport family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroSport
product. You are about to enjoy the comfort of an AeroSport bed. It is your responsibility to read and always follow the safety, care, and maintenance instructions for your new
AeroSport product. Always instruct and supervise others on your bed’s proper use, maintenance, and safety.
IMPORTANT: Preparation of your AeroSport bed requires no tools. Use of tools may damage your bed.
7986 Rev 09/07
109 Pump
Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
WARNING: Adult supervision required for inflation, deflation, and maintenance. This is not a lifesaving device. Do not leave children unattended in or around water.
WARNING: This bed is not designed for use by children under 3 years of age. Children under the age of 3 may suffer serious or fatal injury through suffocation, falling from the
bed or becoming trapped between the bed and a wall or other objects.
WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
- This is not a water toy. Use as a mattress only.
- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.
- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture bed. Remove all sharp objects from area where bed will be
set up and used.
- Product is intended for use as an indoor bed only. Do not step or jump on bed or use as a trampoline. Bed may puncture.
- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.
- Standing, jumping, or walking on the bed may result in injury and/or damage the bed. Do not jump, stand, or walk on this bed. You can hurt yourself or damage the bed if you do.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.
WARNING: This is an electrical product - not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where small children can reach it.
Do not use in or around water.
- Pump and Pump charger are electrical devices. Do not use in or around water. DO NOT place pump where it could fall or be pulled into the water.
- Unplug adapter when not in use.
- Pump not recommended for use by children under six (6) years of age.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Release Valve located at the head of the bed is closed. If the Air Release Valve is open, close it by using 2 thumbs to push
cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it snaps into the valve opening.
3. Remove the protective plastic cap from the valve by turning counter clockwise. Open the protective rubber cap at the end of the pump. Press the mouth
of the pump into position on the inflation/Release Valve and turn clockwise until it locks.
4. A one-quarter turn clockwise automatically starts inflation.
5. At approximately 60 seconds, a high pitch whine of the pump will signal the bed is inflated to full (firmest) capacity. Bed will not over-inflate.
8. Detach pump by turning counter clockwise. Lie on bed and check the firmness. If you want your bed to be softer, depress the botton in the center
of the valve. If the bed becomes too soft, reattach the pump and reinflate the bed until the desired level of firmness is achieved.
IMPORTANT: Be sure to close the protective valve cap after inflation.
Bed / Rechargeable Pump
RECHARGEABLE Ni-Cd PUMP
IMPORTANT: PUMP MUST BE CHARGED FOR 24 HOURS PRIOR TO THE FIRST INFLATION. Use the AC adaper to charge your new AeroSport pump
for 24 hours. For maximum performance, be sure to fully discharge pump before recharging. After initial charge and use, charge pump for 12 HOURS
at a time. Charging your pump for periods shorter or longer than 12 hours will substantially decrease the life of your Ni-Cd pump. In an emergency, a
3 hour charge will provide one inflation, however, continued charging for 3 hour periods will substantially decrease the life of your Ni-Cd pump.
IMPORTANT: ALWAYS store pump and charger in a cool, dry place. DO NOT allow pump or charger to get wet. Allowing pump and/or charger to
get wet will void your warranty.
TO CHARGE / RECHARGE:
a) First, remove pump and charger from box.
b) Second, remove tiny rubber plug from hole on the back of the pump. Insert the charger’s mini-plug in the hole.
c) Third, plug the charger unit into any standard 110V (or 220V depending on your local service) electrical outlet and let it charge for 12 hours
(24 hours on initial charge).
NOTE: For best pump performance, you must completely drain the charge from your pump prior to recharging. For directions, see discharge section below.
Prior To Inflation:
a) Unplug the pump after it has been charged for 12 hours (24 hours on initial charge).
b) Remove charger unit from the electrical outlet and the mini-plug from the pump.
c) Re-insert the tiny rubber plug into the hole on the back of the pump.
NOTE: Pump will not run while charger is plugged into an electrical outlet.
To Discharge:
a) Place pump on valve as if to inflate product.
b) Allow pump to run until the pump motor dies down.
NOTE: When properly used, your pump will hold a full charge for approximately 90 days. When storing pump for longer than 90 days, fully discharge
and recharge pump every 120 days. This will help maximize pump life.
TO USE PUMP INSTANTLY WITHOUT HAVING TO RECHARGE THE NI-CD BATTERIES:
a) First, remove the tiny rubber plug from hole on the back side of the pump.
b) Second, insert the 12-volt DC adapter mini-plug into the hole.
c) Third, plug the DC power cord into a standard 12-volt DC automobile cigarette lighter or accessory 12-volt outlet and turn ignition to the accessory portion.
Do not operate pump while engine is running.
d) When the bed is fully inflated detach pump and unplug the 12-volt adapter from the lighter.
WARNING: Do not leave the pump plugged into the cigarette lighter or 12-volt DC outlet, doing so could damage the life of the Ni-Cd batteries. PUMP
SHOULD ONLY BE USED WITH AERO ADAPTERS PROVIDED. DO NOT USE WITH ANY OTHER ADAPTERS. To avoid against risk of fire, electric shock or
injury to persons, read all instruction before using.
CAUTION! Do not incinerate or disassemble this pump, it could result in an explosion or release of toxic materials. Do not short circuit the pump, it may cause
burns.
IMPORTANT: PUMP CONTAINS NICKEL-CADMIUM BATTERIES. BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.

Summary of content (2 pages)