Use and Care Manual

ManualsBrandsAeroCool ManualsEvaporative CoolersAerocool 10,000 CFM 2 Speed Portable Evaporative Cooler for 3300 sq. ft.

OWNER’S GUIDE

USE AND CARE MANUAL

MODEL MB36, MB24

Congratulations: You have purchased a product of superior

performance and design, which will give the best service

when properly operated and maintained. This cooler is

intended to be used as a convenient roll-around spot

cooler.

This guide was designed to provide you with the information

needed to prepare the unit for roll-around spot-cooling. It

also contains information on how to safely operate, inspect,

maintain and troubleshoot your MasterBlaster evaporative

air cooler.

The rst section contains instructions to prepare your

cooler for roll-around portable service. The second section,

Maintenance, contains operational and maintenance

instructions to aid in keeping your unit in good working

order, while Troubleshooting includes information to help

diagnose and repair commonly encountered problems.

Read all instructions carefully before installation

• This cooler must be connected to 120 volt AC, 60 Hz

(cycle) power only. NOTE: Improper voltage will void the

pump and/or motor warranties and may cause serious

personal injury or property damage.

• This cooler must be plugged into a GFCI protected

receptacle, which has been properly installed in

accordance with all local and national codes. If you are not

sure that the receptacle is GFCI protected, consult with a

qualied electrician.

• This cooler is equipped with a power cord having an

equipment grounding conductor and grounding plug. Do

not attempt to defeat this safety device by removing the

grounding pin.

• Do not step on or rollover power cord with heavy or sharp

objects. Do not operate if plug or cord is damaged in any

way. If the unit is damaged or malfunctions, do not

continue to operate it.

• Remove the plug from the electrical receptacle by pulling

on the plug and not the cord.

• Always disconnect electrical power to unit before

attempting to work on or service your cooler.

• Do not operate with evaporative pad removed.

• Do not operate this cooler (fan motor) with any solid-state

speed control device.

• Do not operate with inlet/outlet grilles removed. Do not

place ngers or any other objects inside the fan section.

Serious risk of personal injury or property damage.

• Never wash your cooler cabinet with a garden hose, water

may harm motor and pump.

NOTE:

• Do not use indoors on carpet or wood oor. Unit may leak

water and could damage ooring or create a slip hazard.

• Do not locate or operate cooler near exhaust or vent pipes

as odors or fumes may be drawn into unit.

• Your warranty does not cover shipping damage. Report all

shipping damage at once to store making the delivery.

• For future reference, record the serial number and

purchase date of your evaporative cooler here:

Serial # ______________________________________________

Purchase Date: _______________________________________

Place of Purchase: ____________________________________

READ THIS FIRST!

WARNING - TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING

Safety

Operation

Maintenance

Trouble Shooting

Parts Replacement

1-999-2439

CAUTION: the use of anode devices, chemical additives or

cooler cleaner treatments in this cooler will void the warranty.

MASTER BLASTER

- -

INITIAL RELEASE

LRC

X/X/2013

ECN

REV.

DESCRIPTION

DATE

REVISION HISTORY

.X = ±.125

.XX = ±.030

.XXX = ±.005

= ± 2°

ALL DIMENSIONS ARE OUTSIDE AND TO

THE CENTER OF ALL HOLES AND SLOTS.

UNLESS OTHERWISE SPECIFIED:

PROPRIETARY NOTICE:

THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN ARE PROPRIETARY DATA

OF PHOENIX MANUFACTURING INC. NEITHER THIS DOCUMENT OR THE INFORMATION

CONTAINED SHALL BE REPRODUCED, USED OR DISCLOSED TO ANY OTHER WITHOUT

WRITTEN CONSENT OF PHOENIX MANUFACTURING INC.

Phoenix Manufacturing Inc.

BLANK NUMBER:

SCALE:

MATERIAL:

DRAWN BY:

DATE:

DRAWING NUMBER:

REVISION:

PART DESCRIPTION:

MIN. BEND RADIUS =

MASTERBLASTER 10K FINAL ASSEMBLY

DO NOT SCALE

S. KANDOV

11/8/2012

SHEET: 1 OF 1

# OF SHEETS:

ALL FLAT PATTERN FEATURES

ARE FORMED UP.

PAGE 1

READ AND SAVE THESE IMPORTANT

SAFETY INSTRUCTIONS

08132013 1-999-2439

Summary of content (4 pages)

PAGE 1
MASTER BLASTER OWNER’S GUIDE USE AND CARE MANUAL MODEL MB36, MB24 Congratulations: You have purchased a product of superior performance and design, which will give the best service when properly operated and maintained. This cooler is intended to be used as a convenient roll-around spot cooler. This guide was designed to provide you with the information needed to prepare the unit for roll-around spot-cooling.
PAGE 2
Fig.
PAGE 3
a. Remove inlet (back) grille from cabinet. b. Remove top pan from cabinet. c. Remove water distributor cover and tube assembly. d. Remove pads by tilting slightly forward and carefully lifting up and out. If passages are clogged or pad is dirty, hose off inlet face of pad. Light, gentle brushing of the inlet edges of the pad with a stiff bristle brush (do not use a wire brush) will not harm the pad and will remove more stubborn scaling. e.
PAGE 4
OPERATING INSTRUCTIONS Note: Do Not Undercoat the Water Reservoir Guidelines and location Your cooler's water reservoir is finished with our Peblar XT® appliance-type finish. It is so hard that asphalt-type cooler undercoating will not stick to it. Undercoating will break free, clogging the pump and water distributor. Always make sure that the roll-around unit is operated on a solid, level surface strong enough to hold its weight (Unit can weigh up to 500lb when full).