Use and Care Manual

ManualsBrandsAeroCool ManualsEvaporative Coolers1500 CFM 2-Speed Portable Evaporative Cooler for 1000 sq. ft.

Congratulations: You have purchased a product of superior

performance and design, which will give the best service when

properly operated and maintained. This cooler is intended to be

used as a convenient roll-around spot cooler.

This guide was designed to provide you with the information

needed to prepare the unit for roll-around spot-cooling. It also

contains information on how to safely operate, inspect, maintain

and troubleshoot your Shop Blaster evaporative air cooler.

The rst section contains instructions to prepare your cooler for

roll-around portable service. The second section, Maintenance,

contains operational and maintenance instructions to aid in

keeping your unit in good working order, while Troubleshooting

includes information to help diagnose and repair commonly

encountered problems.

READ AND SAVE THESE IMPORTANT SAFETY

INSTRUCTIONS

Read all instructions carefully before installation

• This cooler must be connected to 120 volt AC, 60 Hz (cycle)

power only. NOTE: Improper voltage will void the pump and/

or motor warranties and may cause serious personal injury or

property damage.

• This cooler is NOT intended for outdoor use.

• Do NOT exceed a maximum weight of 50 pounds per drawer.

• Do NOT exceed a maximum total weight of 600 pounds

including water and toolbox contents.

• Do NOT have more than one drawer open at a time, the unit may

tip.

• When moving this unit ensure the water has been emptied and

all drawers are closed and locked.

• Ensure the brakes on the two rear casters are engaged when the

unit is not being moved.

• This cooler must be plugged into a GFCI protected receptacle,

which has been properly installed in accordance with all local and

national codes. If you are not sure that the receptacle is GFCI

protected, consult with a qualied electrician.

• This cooler is equipped with a power cord having an

equipment grounding conductor and grounding plug. Do NOT

attempt to defeat this safety device by removing the grounding

pin.

• Do NOT step on or rollover power cord with heavy or sharp

objects. Do NOT operate if plug or cord is damaged in any way. If

the unit is damaged or malfunctions, do NOT continue to operate

it.

OWNER’S GUIDE

USE AND CARE MANUAL

MODEL SB5100

01-999-2534 Page 1

Safety

Operation

Maintenance

Trouble Shooting

Parts Replacement

READ THIS FIRST!

WARNING - TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING

• Always disconnect electrical power to unit before

attempting to work on or service your cooler.

• Do NOT operate with evaporative pad removed.

• Do NOT use this unit as a step stool or ladder. Do not sit or

stand on this unit. Serious risk of personal injury or

property damage may occur.

• Do NOT operate this cooler (fan motor) with any solid-state

speed control device.

• Do NOT operate with pad frame removed. Do NOT

place ngers or any other objects inside the fan section.

Serious risk of personal injury or property damage may occur.

• Never wash your cooler cabinet with a garden hose, water

may harm motor and pump.

• Use of extension cord is not recommended.

NOTE:

• Do not use indoors on carpet or wood oor. Unit may leak

water and could damage ooring or create a slip hazard.

• Do not locate or operate cooler near exhaust or vent pipes

as odors or fumes may be drawn into unit.

• Your warranty does not cover shipping damage. Report all

shipping damage at once to store making the delivery.

• For future reference, record the serial number and

purchase date of your evaporative cooler here:

Serial #____________________________________________

Purchase Date:_____________________________________

Place of Purchase:___________________________________

Summary of content (11 pages)

PAGE 1
OWNER’S GUIDE USE AND CARE MANUAL MODEL SB5100 Congratulations: You have purchased a product of superior performance and design, which will give the best service when properly operated and maintained. This cooler is intended to be used as a convenient roll-around spot cooler. This guide was designed to provide you with the information needed to prepare the unit for roll-around spot-cooling.
PAGE 2
CAUTION: the use of anode devices, chemical additives or cooler cleaner treatments in this cooler will void the warranty. INTRODUCTION Your Shop Blaster evaporative air cooler was thoroughly tested and inspected before leaving the factory. This manual is your guide to economical, trouble free comfort cooling over the years with reasonable care and regular maintenance. Failure to follow these instructions may damage your cooler, impair its operation, and/or void the warranty. Read it carefully.
PAGE 3
Motor and Blower check Remove the pad frame by slightly lifting it from the bottom, pull outwards until clear of cabinet bottom pan, then downwards until frame clears cabinet top. Check motor mounting to be sure all screws and nuts are tightened down properly. Rotate the blower by hand to see that it moves freely without rubbing against housing. Belt Adjustment Correct belt tension and alignment is important as it cuts power consumption and prolongs life of the belt and motor.
PAGE 4
Controls Rocker-type control switches are used to select the operating mode of the cooler. These switches control fan speed (FAN-HIGH/OFF/ LOW) and the pump operation (COOL-ON/OFF). To eliminate a rush of warm air when starting the cooler, be sure to turn the pump (COOL) on for a few minutes before turning on the blower motor (FAN) in low or high speed.
PAGE 5
Line-in Mode: Remote Control Battery: The remote control uses a CR2025 battery. To use line in connect a device using a cord with a 3.5mm audio connector. Volume can still be adjusted through the module but all other controls need to be made on the connected device. Bluetooth Mode: Cleaning CAUTION: Never wash your cooler cabinet with a garden hose; water may harm motor and pump. Motors damaged by water are NOT covered under warranty.
PAGE 6
Cleaning Water Pump & Hose CAUTION: Do not allow pump to fall over and become submerged; water will damage pump motor. Drawer Slides Twice yearly, lubricate the drawer slides with grease or equivalent where shown below. Clean water pump and hose assembly as follows: 1. Unplug pump cord, remove mounting bracket screw and remove pump from cooler. Shake gently to remove water. 2. To prevent breakage, carefully release and remove impeller base plate from the pump body. 3.
PAGE 7
Drawer Installation Pull slides in box to full extension. Align the slides in from the box with the slides on the drawer one at a time. Once both are aligned, push the drawer completely into the box. 3. Lay pad frame on smooth, flat surface with pad retainer up. observe the location / placement of the pad retainer. Remove retainer by sliding it out from under the pad frame flange. Carefully remove and discard old pad. 4.
PAGE 8
WIRING DIAGRAM 01-999-2534 Page 8
PAGE 9
TROUBLESHOOTING: The following guide is intended to help you diagnose and fix some of the most commonly encountered problems; by no means does this guide cover all of the possible problems you may encounter. If you cannot diagnose and correct the problem, or if it persists, contact qualified service personnel. All electrical work should be done by, or with the help of, a qualified electrician. PROBLEMS / SYMPTOMS POSSIBLE CAUSE CORRECTIVE ACTION Water draining from the unit 1.
PAGE 10
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Item Part Number SB5100 - Replacement Parts List Replacement Part Louver Panel Assembly 05-002-0427 05-001-0145 SB5100 - Cover Replacement05-004-0003 Parts List Switch Box 2 3" Celdek Media (Set of 2) 1 3 Replacement Part Water Distributor Assembly Part Number 05-006-0193 4 29 28 27 26 Toolbox Drawer Slides (not shown) Toolbox Key (not shown) Radio Remote Control (not shown) Outlet Cover Duplex Outlet
PAGE 11
Evaporative Cooler - Limited Warranty Phoenix Manufacturing, Inc., Phoenix Arizona, extends this limited warranty to the original purchaser of this evaporative cooler. What this warranty covers and for how long: FIVE YEAR COVERAGE: Phoenix Manufacturing Inc. will exchange the cabinet only should any water leakage occur through the base assembly due to rust out, or as a result of defect in material or workmanship during the first five years from the date of initial purchase.