Data Sheet

Produktinformation
ÄRONIX Siliconöl - mittelviskos - Silicone Fluid
Colorless, clear polydimethylsiloxane fluid
FEATURES
• Ease of application and rubout
• High water repellency
• High compressibility
• High shearability without breakdown
• High spreadability and compatibility
• Low environmental hazard
• Low fire hazard
• Low reactivity and vapor pressure
• Low surface energy
• Good heat stability
• Essentially odorless, tasteless and nontoxic
• Soluble in a wide range of solvents
COMPOSITION
• Polydimethylsiloxane polymers
• Chemical composition (CH3)3SiO[SiO(CH3)2]nSi(CH3)3
APPLICATIONS
• Various applications including cosmetic ingredient, elastomer
and plastics lubricant, electrical insulating fluid, foam preventive or
breaker, mechanical fluid, mold release agent, surface active
agent, and solvent-based finishing and fat liquoring of leather
DESCRIPTION
ÄRONIX Siliconöl – mittelviskos is a polydimethylsiloxane polymer
manufactured to yield essentially linear polymers in a wide range
of average kinematic viscosities.
HOW TO USE
ÄRONIX Siliconöl – mittelviskos is highly soluble in organic
solvents such as aliphatic and aromatic hydrocarbons, and the
halocarbon propellants used in aerosols.
PRODUCT SAFETY INFORMATION
ÄRONIX Siliconöl – mittelviskos 50-1,000 CS may cause
temporary eye discomfort.
USABLE LIFE AND STORAGE
Product should be stored at or below 60°C (140°F) in the original
unopened containers.
LIMITATIONS
This product is neither tested nor represented as suitable for
medical or pharmaceutical uses. Not intended for human injection.
Not intended for food use.
LIMITED WARRANTY INFORMATION – PLEASE READ
CAREFULLY
The information contained herein is offered in good faith and is
believed to be accurate. However, because conditions and
methods of use of our products are beyond our control, this
information should not be used in substitution for customer’s tests
to ensure that our products are safe, effective, and fully
satisfactory for the intended end use. Suggestions of use shall not
be taken as inducements to infringe any patent.
Dow Corning’s sole warranty is that our products will meet the
sales specifications in effect at the time of shipment.
Your exclusive remedy for breach of such warranty is limited to
refund of purchase price or replacement of any product shown to
be other than as warranted.
DOW CORNING SPECIFICALLY DISCLAIMS ANY OTHER
EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR MERCHANTABILITY.
DOW CORNING DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. PRODUCT SAFETY INFORMATION
REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT.
BEFORE HANDLING, READ PRODUCT AND MATERIAL SAFETY DATA
SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL,
ENVIRONMENTAL, AND HEALTH HAZARD INFORMATION. PLEASE
REQUEST THE SAFETY DATA SHEET.
TYPICAL PROPERTIES
Specification Writers: These values are not intended for use in preparing specifications.
Test Unit Result
Appearance Crystal clear
Specific Gravity at 25°C (77°F) 0.970
Refractive Index at 25°C (77°F) 1.4035
Color, APHA 5
Flash Point, Open Cup °C (°F) >326 (>620)
Acid Number, BCP trace
Melt Point °C (°F)
1,2
25 (-13)
Pour Point °C (°F) 50 (-58)
Surface Tension at 25°C (77°F) dynes/cm 21.2
Volatile Content, at 150°C (302°F) percent 0.11
Viscosity Temperature Coefficient 0.61
Coefficient of Expansion cc/cc/°C 0.00096
Thermal Conductivity at 50°C (122°F) g cal/cm·sec °C 0.00038
Solubility Parameter
3
7.4
Solubility in Typical Solvents
Chlorinated Solvents High
Aromatic Solvents High
Aliphatic Solvents High
Dry Alcohols Poor
Water Poor
Fluorinated Propellants High
Dielectric Strength at 25°C (77°F) volts/mil 400
Volume Resistivity at 25°C (77°F) ohm-cm 1.0x10
15
1
The melt point temperature is a typical value and may vary somewhat due to molecular distribution. If the melting point is critical to your
application, then several lots should be thoroughly evaluated.
2
Due to different rates of cooling, this test method may yield pour points lower than the temperature at which these fluids would melt.
3
Fedors Method: R.F. Fedors, Polymer Engineering and Science, Feb. 1974.
ÄRONIX-Produkte – Peter Magin
Albert-Einstein-Str. 5 69190 Walldorf Tel.: 06227 / 359840 www.aeronix.de Mail: [e-mail]