Flycolor_ESC_Manual

Thank you for purchasing our product. Any Improper operation may cause personal injury damage to the
product and related equipments. This high power system for RC model can be dangerous ,we strongly
recommend reading the user manual carefully and completely. We will not assume any responsibility for any
losses caused by unauthorized modifications to our product. We have the right to change the design,
appearance, performance and usage requirements of the product without notice.
ATTENTION
01 Main features
02 Specification
03 Connection diagram
04 Dimensions
05 Operation instruction
2.Calibrate Throttle Range
1.Normal start-up
ATTENTION
● Start-up Protection:ES C will cut off output if it fails to start the motor within 3 seconds by accelerating throttle. you need to move the throttle stick
back to the bottom position and restart the motor.( The possible causes : Bad connection or disconnection between ES C & motor , propellers are
blocked, etc)
● Over-load Protection: ES C will cut off power or output when the load suddenly increases to a very high value, normal operation will resume after
moving the throttle stick to the bottom position. ES C will automatically try to restart when ESC and motor are out-of-step.
● Throttle Signal Loss Protection: When E SC detects the loss of throttle signal for over 0.32 seconds, it will cut off power or output immediately to
avoid an even greater loss caused by the continuous high speed rotation of propellers. E SC will resume the corresponding output after the normal
signal is restored.
06 Protections
07 Attentions
3.Set Timing
08 Trouble shooting
User Manual
Multi-Rotor Brushless ESC
● ESC uses high erformace MCUp with 48 MHz frequency.
● Optimized firmware is specialized for disc motor, excellent compatibility.
● The firmware is specialized for multi-rotor , uses AS CF technology ( ),higher Active Switch Continued Flow
efficiency, significantly reduce the heat when ESC’s working.
● S Nano coating, splash waterproof.maller volume;
● Strong self-adaptable firmware, 4 timing options, very simple to use.
● Supports frequency of throttle signal to 500Hz max , compatible with various kinds of flight control.
( ≥500Hz throttle signal is nonstandard signal )
● Supports single LiPo battery voltage up to 4.35V.
● Switches on the bottom Support ：1.Motor rotation change .2. ASCF function on/off .
*Please ensure all solder joints are insulated with heat shrink where necessary.
All pictures are for reference only.
Turn on the transmitter, move the
throttle stick to the bottom position
Connect ESC & battery packs, wait for 2 seconds, motor emits
continuously 1 long and 1 short tone. It means the ES C is ready
for working.
Turn on the
transmitter,
move the
throttle stick to
the top position.
Connect the receiver to
the battery, ensure the
communication is normal
between the transmitter
and receiver, then power
on the ESC.
Wa it for 2 s econd, a fter
motor emits 2 short "B EEP-
B EE P ",m ove the throttle
stick to the bottom position
in 3 seconds.
Wait for 2 seconds, motor
emits continuously 1 long and
1 short tone. It means the ESC
is ready for working.
Attention：Please calibrate throttle range when first time to use ESC or change transmitter.
Wait for 2 seconds, motor
emits continuously 1 long
and 1 short tone. It means
the ESC is ready for working.
Turn on the
transmitter,
move the
throttle stick
to the top
position.
Connect the receiver
to the battery, ensure
the communication is
normal between the
transmitter and
receiver, then power
on the ESC.
The motor will
emit different
tone circularly.
Move the throttle stick
to the bottom position
in 3 seconds after
hearing corresponding
tone, the setting will be
completed.
“Beep-beep-”Throttle rage;
“Beep-beep-beep-” 15° timing
“Beep-beep-beep-beep-”18.75° timing
“Beeeep--” 22.5° timing
“Beeeep--beep-” 26.25° timing
( When motor emits tone times ≥5 times, long " Beep--" will represent 5 times)
When ES C drives disc type motor with accelerating throttle , motor may be out-of-step ,
stalling or requires higher speed , you could try to change timing ( E SC factory default
value is 22.5°). Higher timing can accelerate motor speed, but also cause more heat.
After changing timing, please test on the ground before flying.
● Reasonable use of E SC can prolong the service life. please clean up the water and stains on the ESC after a certain period of time , to avoid electric
short circuit.
● User need to calibrate the throttle range when starting to use a new E SC or change another transmitter.
● When some abnormality occurs in ES C driving the motor or need the motor to reach a higher RPM, user can try to change the timing.
● ASCF ON /OF F function, must ensure all ES Cs setting consistent, it will take effect after power on again.
● Motor rotation function ,it will take effect after power on again.
● Please contact Flycolor sales or technical support for more information.
Trouble
ES C was unable to
start the motor
ES C was unable to
start the motor
“Beep beep beep…”
Urgent short tone
Warning Tone
“Beep,beep,beep…”
Time interval is 1 second
Possible Cause
The throttle stick is not at the bottom
position or throttle range is too small.
No output signal from the throttle
channel on the receiver.
ES C was unable to
start the motor
“Beep-beep,beep-beep-beep,…
Beep--beep-” Circular tones
The”Normal/Reverse”direction of the
throttle channel on transmitter is incorrect.
Solution
Move the throttle stick to the bottom position or reset
the throttle range.
Check if the communication is normal between
transmitter and receiver; Check throttle channel
connection well.
Refer to the transmitter instruction and adjust the
setting of “Normal/Reverse”direction of the throttle
channel.
251400-1069, V1.0
11.7 mm
29.5 mm
46 mm
64.6 mm
BE C
Con. Current
Burst Current
(10S)
Size
(for reference)
Weight
(for reference)
LiPo cellsModel
FlyDragon SLIM-60A
60A 80A
4-6S
56g
No
SLIM
TM
FlyDragon
FlyDragon SLIM
64.6x29.5x11.7mm
BEC
Batter y
Receiver
Motor
Signal cable
ESC
ASCF
ON OFF
Rotation
Rev. Nor.
Switches Support to：
1.Change Motor rotation .（Normal is default）
2.AS CF function On/Off .（ON is default）
www.flycolor.net