Product Manual

No. 41240 - 03/12
LED SAFETY VEST
PRODUCT NUMBERS: 1241 - FLUORESCENT YELLOW - LARGE
1242 - FLUORESCENT YELLOW - X-LARGE
1243 - FLUORESCENT YELLOW - XX-LARGE
I. GENERAL DESCRIPTION
Description: The Aervoe LED Safety Vest is made of a 100%
Polyester high-visibility mesh material. A heavy-duty metal
zipper secures the front closure and the sides are adjustable
with hook and loop straps. Two vertical 2" reective stripes run
front to back over the shoulders and one horizontal stripe runs
across the waist. 8 LED lights are embedded in the vertical
reective tape on the front and back of the vest. 2-AA batteries
are required to operate the LED lights (not included).
Benefits: This vest is appropriate for moderate-risk
environments including poor weather conditions and trafc
approaching over 25 MPH. The LEDs increase visibility from
just reective tape alone.
Application: Surveying, highway and road construction, utility
work, and emergency response.
Directions: Remove battery housing from the inside pocket
located on the front left side of the vest. Slide the cover open
until it stops. Insert 2-AA batteries and close the cover. Turn
the lights on and off by pushing the button located on the end
of the battery housing and return to the inside vest pocket.
Cleaning Instructions: Do not submerge to clean. Spot
treat fabric with soap and water. Air dry only. No not bleach,
iron, or dry-clean.
Limitations: The reective stripes and LED lights on this vest
enhance visibility but cannot guarantee adequate visibility in all
situations. Weather conditions, your surroundings, keeping the
reective material clean, and installing fresh batteries to power
the LEDs will contribute to overall performance. Misuse and
poor maintenance may reduce visibility and result in serious
bodily injury.
Packaging:
Each 10.7 oz. (0.3 kg) 8" W x 14" L x 1.75" H 0.11 CF (0.003 CM)
12 vests/case 8.5 lbs. (3.9 kg) 8" W x 14" L x 21" H 1.36 CF (0.04 CM)
Product Data Sheet
Aervoe Industries, Inc.
P.O. Box 485, Gardnerville, NV 89410
0HONEs&AXs#USTOMER3ERVICE
WWWAERVOECOMsMAILBOX AERVOECOM
Minimum areas of visible material - ANSI/ISEA 107-2010
Performance Class 3 Performance Class 2 Performance Class 1
Background material 1240 in
2
(0.80 m
2
) 775 in
2
(0.50 m
2
) 217 in
2
(0.14 m
2
)
Retroreective or combined-performance material
used in conjunction with background material
310 in
2
(0.20 m
2
) 201 in
2
(0.13 m
2
) 155 in
2
(0.10 m
2
)
Combined-performance material used without
background material
N/A N/A 310 in
2
(0.20 m
2
)
Minimum width of retroreective material 2 in (50 mm) 1.375 in (35 mm) 1 in (25 mm)
or
2 in (50 mm) combined-
performance material (without
background material)
Minimum number of yards per retroreective
material width
4.3 yds or 2 in (50 mm) width 4 yds of 1.375 in (35 mm)
width 2.8 yds or 2 in (50 mm)
width
4.3 yds of 1 in (25 mm) width
3.1 yds of 1.372 in (35 mm)
width 2.15 yds of 2 in (50 mm)
width
Photometric performance (consult the ANSI/ISEA
107-2010 standard for Tables 4 and 5)
Level 2 (Table 4) or Level 1
(Table 5)
Level 2 (Table 4) or Level 1
(Table 5)
Level 2 (Table 4) or Level 1
(Table 5)