Specifications

ACUO 908
AEV Broadcast Srl
Tel. [phone]
Fax [phone]
Room & Studio section
Control Studio selection
1 – Button for selecting the EXT
input
routing it to the Control Studio
output
2 –
Button for selecting the master PGM output
for routing it to the Control Studio
output
3 –
Button for selecting the master UTL output
for routing it to the Control Studio
output
4 –
Button for selecting the master AUX output
for routing it to the Control Studio
output
5 –
Button for selecting the CUE bus
it to the Control Studio output.
Control Room selection
6 –
Button for selecting the EXT input
routing it to the Control Room
outputs
7 –
Button for selecting the master PGM output
for routing it to the Control Room
output
8 – Button for selecting the ma
ster UTL output
for routing it to the Control Room
output
9 –
Button for selecting the master AUX output
for routing it to the Control Room
output
Master setup
Master knob jog ; directly it
select the Gain
in sequence, the fol
lowing commands:
1
th
push-buttom
Control Room level (
2
th
push-buttom
Control Studio level
3
th
push-buttom
PGM output level
4
th
push-buttom Ex
ternal input level
5
th
push-buttom
CUE interlock (OFF/ON)
6
th
push-buttom
PGM Digital sample rate
7
th
push-buttom
UTL Digital sample rate
8
th
push-buttom
channel’s selection to GPIO 1
9
th
push-buttom
channel’s selection to
10
th
push-buttom
channel’s selection to GPO 3 ( Start/STOP C) command
1
2
3
4
5
ACUO 908
Serie - AEV ON AIR CON
SOLE
AEV Broadcast Srl
, via della Tecnica 33 –
40050 Argelato (BO) Italy
Fax [phone]
Web site www.aev.eu
11
Room & Studio section
input
for
output
.
Button for selecting the master PGM output
output
.
Button for selecting the master UTL output
output
.
Button for selecting the master AUX output
output
.
Button for selecting the CUE bus
for routing
Button for selecting the EXT input
for
outputs
.
Button for selecting the master PGM output
output
s.
ster UTL output
output
s.
Button for selecting the master AUX output
output
s.
Talk Back
10 – Button to active
the
Control Studio outputs.
Talk back Regia
to Studio
When the TB (talk back) button is pressed, the
signal of the enabled microphone is sent to the
Control Studio output.
•
Channel with function talkback to studio
(TBST: ON)
• Channel in STOP
What happens:
• t
he Talk back button of the remote fader
lights up
•
the previous selection of the Control Studio
flashes
•
the audio signal present in the Control studio
is replaced by the channel selected in TB
Talk back Studio to
Regia
(need the
Remote Fader
• Channel
connected to the Remote Fader unit
ta
lkback function activated (ST
• Channel in STOP
What happens
when the remote TB (talk back)
button is pressed:
•
the Talk back button of
•
the previous selection of the Control
flashes
•
the audio signal present in the Control Room
is re
placed by the channel connected to the
Remote Fader unit
•
the signal of the enabled microphone is sent
to the Control Room output.
select the Gain
headphone level, the range is -
∞ ÷ +8 dB
lowing commands:
Control Room level (
-∞ ÷ +8 dB)
Control Studio level
(-∞ ÷ +8 dB)
PGM output level
(-12 ÷ +12 dB)
ternal input level
(-12 ÷ +12 dB)
CUE interlock (OFF/ON)
PGM Digital sample rate
( 32, 44.1, 48, 96 KHz )
UTL Digital sample rate
( 32, 44.1, 48, 96 KHz )
channel’s selection to GPIO 1
( Start/STOP A) command
channel’s selection to
GPIO 2 ( Start/STOP B) command
channel’s selection to GPO 3 ( Start/STOP C) command
6
7
8
9
10
SOLE
40050 Argelato (BO) Italy
e-mail [e-mail]
the
Talkback function to the
to Studio
:
When the TB (talk back) button is pressed, the
signal of the enabled microphone is sent to the
Channel with function talkback to studio
he Talk back button of the remote fader
the previous selection of the Control Studio
the audio signal present in the Control studio
is replaced by the channel selected in TB
Regia
:
Remote Fader
)
connected to the Remote Fader unit
with
lkback function activated (ST
CR: ON)
when the remote TB (talk back)
the Talk back button of
ACUO flashes
the previous selection of the Control
Room
the audio signal present in the Control Room
placed by the channel connected to the
the signal of the enabled microphone is sent
to the Control Room output.
∞ ÷ +8 dB
;