Owner`s manual

2008 AFG Service Seminar [rev 1.3] | 45
Section Two | Engineering Mode
Engineering Mode
>> Ellipticals | Bikes
Note: At Any time, Press and hold the STOP button to exit the engineering menu.
Entering the Engineering Mode
1 | Turn the elliptical power to ON.
2 | Simultaneously press and hold (for about three seconds) the resistance “+” (s) and “-” (t) buttons.
3 | The console should beep two times and ENG0 (EN90) should be displayed in the time window, “ENGINEERING
MENU” scrolls in matrix or is static in the text box.
Note: To navigate through the engineering menu, use the resistance and/or the incline “+” (s) or “-” (t) buttons.
Display Test (Eng0)
Information (Eng3)
Eng0 appears in the time window.
DISPLAY TEST will scroll in the matrix or will be static in text
box.
Press ENTER to select.
When selected each display segment should be lit up.
When pressed each button should have a unique display change.
-Stop button turns off all lights.
-Start button turns all lights on.
Eng3 appears in the time window.
INFORMATION will scroll in the matrix or will be static in text
box.
Press ENTER to select.
ACCUMULATED will scroll in matrix.
-Time window will show accumulated time.
-Distance window will show accumulated distance.
-If Time and Distance are in the same window, the time will
show F00 and the distance will show F01. Press“+” (s) or “-” (t)
to change.
Note: If console has an accumulated reset function, hold Start
for 5 seconds to reset. This will not apply to most
models.
Hardware Test (Eng1)
Eng0 appears in the time window.
HARDWARE TEST will scroll in the matrix or will be static in
text box.
Press ENTER to select.
-Resistance “+” (s) or “-” (t) will change the resistance.
-Incline “+” (s) or “-” (t) will change the incline.
-Quick incline keys will beep but do not function.
-Incline motor will stop at minimum or maximum incline (not
continue to move) if “+” (s) or “-” (t) is held.
Incline Test (Eng4)
Eng4 appears in the time window.
INCLINE TEST will scroll in the matrix or will be static in text
box.
Press ENTER to select.
Note: This menu is only for incline ellipticals. All other bikes and
ellipticals will not have this menu.
-MIN ADC will how in the text box. The ADC value will be the
current height.
-Change the value with the incline “+” (s) or “-” (t). Range=
100-250. Press Enter to save the value. If the value is out of range
then OUT OF RANGE will show and the value will not be saved.
-ADC IS SAVED will show for three seconds if the value is in
range.
-Press resistance “+” (s) to change the Max.
-MAX ADC will show in the text box. The ADC value will show
the current height.
-Change the value with the incline “+” (s) or “-” (t).
Range=550-750. Press enter to save the value. If the value is out
of range, OUT OF RANGE will show and the value will not be
saved.
-ADC IS SAVED will show for three seconds if the value is in
range.
-Press resistance “-” (t). to change the Min.
Switch Function (Eng2)
Eng2
appears in the time window.
SWITCH FUNCTION will scroll in the matrix or will be static in
text box.
Press ENTER to select.
If the treadmill has a Demo Mode then:
-The brickyard will scroll “DEMO ON” or “DEMO OFF”.
-Default will be “DEMO ON”.
-The “+” (s) or “-” (t) buttons will change the Demo on/off
settings.
Start Selects miles or km.
-The display will show “0” for miles or “1” for km.
-The display will scroll “MILES” OR “KM” when Start is pressed
to change.
-The new setting is automatically saved when Start is pressed,
no other buttons need to be pressed to save.
-Enter changes the ep/bi setting. Display will show EP for ellipti-
cal and BI for bike.
-The new setting is automatically saved when Enter is pressed,
no other buttons need to be pressed to save.