User`s guide

8
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
9
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY STEP 2
NYLON
NUT (E)
Qty: 6
LARGE “O” RING
Qty: 1
ARC WASHER (D)
Qty: 12
BOLT (B)
95 mm
Qty: 4
BOLT (F)
90 mm
Qty: 2
HARDWARE BAG 2 CONTENTS :
RIGHT
SUPPORT
FRAME
CENTER
SUPPORT FRAME
LARGE
“O” RING
NYLON NUT (E)
LEFT SUPPORT
FRAME
UPPER PULLEY
ASSEMBLY
ARC WASHER (D)
BOLT (A)
ARC WASHER (D)
BOLT (F)
ARC WASHER (D)
SEAT
WELDMENT SET
SEAT
ADJUSTMENT
PIN
SEAT SAFETY PIN
NUT (E)
ASSEMBLY STEP 3
NYLON
NUT (E)
Qty: 2
NYLON
NUT (K)
Qty: 1
FLAT
WASHER (C)
Qty: 10
BOLT (F)
25 mm
Qty: 2
BOLT (G)
92 mm
Qty: 1
FLAT
WASHER (I)
Qty: 2
BOLT (H)
20 mm
Qty: 4
BOLT (J)
83 mm
Qty: 2
LOCK
WASHER (L)
Qty: 2
HARDWARE BAG 3 CONTENTS :
BOLT (G)
BOLT (J)
BOLT (J)
LEG ROLLER
SUPPORT TUBE
LOWER
CONNECTION TUBE
FLAT WASHER (I)
FLAT WASHER (C)
NYLON NUT (E)
NYLON NUT (K)
FLAT
WASHER (C)
LOCK
WASHER (L)
RADIAL ARM
ASSEMBLY
NYLON NUT (E)
CENTER
CONNECTION
TUBE
LEFT
CONNECTION
TUBE
CENTER
SUPPORT
FRAME
RIGHT CONNECTION TUBE
BOLT (H)
FLAT WASHERS (C)
BOLT (F)
Open HARDWARE BAG 2.
Slide LARGE “O” RING
onto CENTER SUPPORT
FRAME as shown in
diagram.
Attach UPPER PULLEY
ASSEMBLY to CENTER
SUPPORT FRAME using
4 BOLTS (F) and 4 ARC
WASHERS (D) and 2
NYLON NUTS (E). Tighten
this hardware.
Attach UPPER PULLEY
ASSEMBLY to RIGHT
MAIN SUPPORT FRAME
using 2 BOLTS (B), 4
ARC WASHERS (D) and 2
NYLON NUTS (E).
Attach UPPER PULLEY
ASSEMBLY to LEFT
SUPPORT FRAME using
2 BOLTS (B), 4 ARC
WASHERS (D), and 2
NYLON NUTS (E).
Install SEAT WELDMENT
SET onto posts on
CENTER SUPPORT FRAME
as shown in diagram, and
insert SEAT SAFETY PIN.
Install SEAT ADjUSTMENT
PIN into SEAT WELDMENT
SET as shown in
diagram. (Fully thread
into SEAT WELDMENT
SET after SEAT BOTTOM
ADjUSTMENT BAR is
installed.)
A
B
C
D
E
F
G
Open HARDWARE BAG 3.
Remove STOPPER from front side of RADIAL ARM ASSEMBLY and reinstall on back side.
Tighten both STOPPERS.
Attach RADIAL ARM ASSEMBLY to CENTER SUPPORT FRAME using 2 BOLTS (F), 2 LOCK
WASHERS (L) and 2 FLAT WASHERS (C). Tighten this hardware.
Attach RIGHT SIDE CONNECTION TUBE to SEAT WELDMENT SET and to LOWER
CONNECTION TUBE using 2 BOLTS (H) and 2 FLAT WASHERS (C), as shown in diagram.
Repeat on left side.
Attach CENTER CONNECTION TUBE to SEAT WELDMENT SET and to LOWER CONNECTION
TUBE using 2 BOLTS (j), 4 FLAT WASHERS (C) and 2 NYLON NUTS (E).
Attach LEG ROLLER SUPPORT TUBE to LOWER CONNECTION TUBE using 1 BOLT (G), 2
FLAT WASHERS (I) and 1 NYLON NUT (K). Tighten all hardware in Step 3.
A
B
C
D
E
F
G
RADIAL ARM ASSEMBLY
STOPPER
STEP 3-B: INSTALLING THE STOPPER:
2.0AS_Rev.1.5.indd 8-9 9/23/08 10:14:19 AM