Instructions / Assembly
Table Of Contents
- How to use this manual
- Contents
- DO NOT OPERATE THE SCOOTER BEFORE READING AND UNDE
- WARNING
- Intended Use
- Assembly
- Battery Charging
- Typical Use
- Control Functions
- Transporting
- TIP:
- Important:
- Getting on to your scooter
- Getting off your scooter
- Hand Controls
- The Preset Speed Knob
- The Battery Gauge
- TIP:
- Operating the Lights
- Throttle Lever
- Horn Button
- Key Switch
- Off Board Charging Socket
- WARNING.
- WARNING:
- Removing the Seat
- Note: Exercise caution when lifting the seat.
- Seat Adjustment
- Armrest Adjustment
- Tiller Adjustment
- Battery Removal
- Battery Replacement
- Off-Board Battery Charger
- Note:
- 1.RED = Power is on.
- The off-board charger must be kept dry in temperat
- Packaging
- Important
- Transportation
- TIP:
- Packaging and transportation environment condition
- Basic Driving
- Important:
- Traveling across slopes
- Do not traverse across the face of a slope in exce
- Note: Automatic braking is not instantaneous and w
- Switching off
- Use on the footpath
- P12.4
- Crossing roads
- Note: Low speed settings are recommended when trav
- Use of mobile phones
- Tyres
- Emergency Braking
- Caution!
- Freewheel mechanism
- General information
- Batteries
- Maintenance free
- Battery care
- Battery pack care plan
- Do not leave the charger still connected to the ba
- Caution
- Caution!
- The range of your vehicle
- Note: If you are out on your scooter and the batte
- We specifically disclaim responsibility to all per
- Attention: Switch on the scooter lights (if fitted
- Failure to comply with the above requirements coul
- This scooter has been tested to ISO 7176 Part 9 “C
- Maximum User Weight Limitations.
- DISPOSAL
- CAUTION:
- EMC sources can be broadly classified into three t
- Note: Other types of hand-held devices such as cor
- Note:
- Notes:
- Warnings
- Attachments：
- Storage
- Electronic faults
- Wheels
- Warranty condition
20
Transportation
Your scooter may be disassembled quickly and simply for transportation.
1. Switch off the scooter, make sure the motor is engaged.
2, Remove the basket.
3.
Remove the seat, leaving the seat stem in position.
4.
Place the basket on the floor mat appropriately(photo 11-1).
5.
Lower the tiller, using the folding knob, to its lowest setting locking in the
basket. Make sure that there is at least 30mm between Tiller and battery
pack(photo 11-5).
6.
Using the lifting handles provided carefully lift the scooter safely and
securely into the luggage compartment of the vehicle(photo 11-6,7).
TIP:
1.
Please put all the parts after disassembling into the original carton
from us to insure the safe transportation.
2.
To reverse the above steps to reassemble your scooter.
Important:
When reassembling the scooter, remember to insert the battery lockingpin,
because failure to do so may result in the batteries disengaging during use.
Always secure your scooter parts before transportation. Remember to
engage the drive unit by pushing the freewheel lever forwards to stop the
scooter from moving. Don’t sit on the scooter during transportation.
P11-5 P11-6 P11-7
Packaging and transportation environment conditions
The mobility scooters can be transported by common transportation
vehicles, but you need to prevent them from strong impact, vibrating or any
snow or rain. This is clarified in the order contract.
The packaged scooters should be put into an environment between
-20 ℃ ～ 45 ℃ temperature, and humidity less than 93%, no congeal or
corrosive air with good ventilation.