Instructions / Assembly
Table Of Contents
- How to use this manual
- Contents
- DO NOT OPERATE THE SCOOTER BEFORE READING AND UNDE
- WARNING
- Intended Use
- Assembly
- Battery Charging
- Typical Use
- Control Functions
- Transporting
- TIP:
- Important:
- Getting on to your scooter
- Getting off your scooter
- Hand Controls
- The Preset Speed Knob
- The Battery Gauge
- TIP:
- Operating the Lights
- Throttle Lever
- Horn Button
- Key Switch
- Off Board Charging Socket
- WARNING.
- WARNING:
- Removing the Seat
- Note: Exercise caution when lifting the seat.
- Seat Adjustment
- Armrest Adjustment
- Tiller Adjustment
- Battery Removal
- Battery Replacement
- Off-Board Battery Charger
- Note:
- 1.RED = Power is on.
- The off-board charger must be kept dry in temperat
- Packaging
- Important
- Transportation
- TIP:
- Packaging and transportation environment condition
- Basic Driving
- Important:
- Traveling across slopes
- Do not traverse across the face of a slope in exce
- Note: Automatic braking is not instantaneous and w
- Switching off
- Use on the footpath
- P12.4
- Crossing roads
- Note: Low speed settings are recommended when trav
- Use of mobile phones
- Tyres
- Emergency Braking
- Caution!
- Freewheel mechanism
- General information
- Batteries
- Maintenance free
- Battery care
- Battery pack care plan
- Do not leave the charger still connected to the ba
- Caution
- Caution!
- The range of your vehicle
- Note: If you are out on your scooter and the batte
- We specifically disclaim responsibility to all per
- Attention: Switch on the scooter lights (if fitted
- Failure to comply with the above requirements coul
- This scooter has been tested to ISO 7176 Part 9 “C
- Maximum User Weight Limitations.
- DISPOSAL
- CAUTION:
- EMC sources can be broadly classified into three t
- Note: Other types of hand-held devices such as cor
- Note:
- Notes:
- Warnings
- Attachments：
- Storage
- Electronic faults
- Wheels
- Warranty condition
28
14.General Warnings
PERSONAL & OPERATIONAL GUIDELINES
Drive profiles should only be adjusted by healthcare professionals and
approved agents/dealers, who are totally conversant with the process.
They must also fully understand the user’s capabilities and the user’s ability
to operate the scooter safely.
Incorrect settings may cause injury or damage to the user, bystanders, the
scooter and/or nearby property.
To determine personal mobility limitations, practice combinations of
bending, reaching, mount and dismount techniques, whilst in the presence
of a healthcare professional. Practice the above techniques BEFORE
actively using the scooter.
For users with balance problems, practice the above techniques with the
aid of an assistant, in the presence of a healthcare professional.
DO NOT attempt to pick up objects that cause you to shift your weight in
the seat, or require you to bend excessively in any direction. Such action
may result in the scooter tipping over, or in injury to the person or both.
DO NOT use an escalator to move the mobility scooter between floors as
serious bodily injury could arise from such actions.
DO NOT drive on the road, dual carriageways or motorways.
DO NOT drive up, down or across inclines that have water, ice, oil or any
other slippery substance on the surface. Failure to note the above
conditions could cause loss of control.
DO NOT attempt to drive over kerbs or obstacles in excess of 45mm.
Disregarding this warning could cause the mobility scooter to tip resulting in
possible bodily harm.
DO NOT make sharp turns in forward or reverse at high speeds.
DO NOT lift the mobility scooter by its Tiller, Seat, Body Panels or by any
detachable assemblies. Always disassemble the scooter into its stowable
parts and then lift each assembly one at a time.
DO NOT carry passengers on your scooter.
DO NOT attempt to tow another vehicle.
DO NOT operate the mobility scooter without first checking that it is safe to
do so. Always be aware of your surroundings.
DO NOT attempt to use your mobility scooter without first checking that all
wiring harnesses are connected and all detachable parts/assemblies are
correctly aligned and firmly fixed in place.