Use and Care Manual

ManualsBrandsAfterglow ManualsFire PitsColton 34.5 in. Steel Fire Pit in Textured Black Finish

COLTON SQUARE GAS FIRE PIT

ITM./ART.#: 506105F170263

MODEL#: F170263

ANS Z21.97/CSA 2.41-2014

Outdoor Decorative Gas Appliances

Installer: Leave these instructions with consumer.

Consumer: Keep these instructions for further reference.

WARNING: For Outdoor Use Only.

DANGER

If you smell gas:

Shut off gas to the appliance.

Extinguish any open flame.

If odor continues, keep away from the

appliance and immediately call your

gas supplier or fire department.

WARNING

Do not store or use gasoline, or other

flammable vapors and liquids,in the

vicinity of this or any other appliance.

An LP-cylinder not connected for use

shall not be stored in the vicinity of

this or any other appliance.

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has

no odor.

Never use this appliance in an enclosed space such as a

camper, tent, car or home.

Using it in an enclosed space can kill you.

Questions, Problems, Missing Parts?

Before returning to your retailers, contact

Foremost Groups Customer Relations

Department toll free number at 1-800-443-1410

(USA) between the hours of 8:30 am and 5:00

pm EST, Monday thru Friday or fax your

request to (973) 428-8026 or email us at

customerservice@foremostgroups.com

WARNING:

Improper installation,

adjustment, alteration, service

or maintenance can cause injury or property damage.

Read the installation, operating, and maintenance

instructions thoroughly before installing or servicing

this equipment.

Summary of content (16 pages)

PAGE 1
COLTON SQUARE GAS FIRE PIT ITM./ART.#: 506105F170263 MODEL#: F170263 ANS Z21.97/CSA 2.41-2014 Outdoor Decorative Gas Appliances Installer: Leave these instructions with consumer. Consumer: Keep these instructions for further reference. DANGER WARNING If you smell gas: Shut off gas to the appliance. Extinguish any open flame. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. DANGER WARNING: For Outdoor Use Only.
PAGE 2
IMPORTANT SAFETY INFORMATION 1. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1●NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable. 2.
PAGE 3
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S. Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable. 2. The LP-gas supply cylinder to be used must have a listed overfilling prevention device (See Figure 1). 3.
PAGE 4
PACKAGE CONTENTS A Q B J C L K N D I R P PART DESCRIPTION O H F G M QUANTITY PART E DESCRIPTION QUANTITY A Lid 1 L Upper beam 1 B Table Top 1 M Back-left leg 1 C Back panel 1 N Weather cover 1 D Back-right leg 1 O Door handle 1 E Right panel 1 P Foot glider 4 F Front-right leg 1 Q Lava rock (13.
PAGE 5
ILLUSTRATED PARTS LIST A Lid B Table Top C Back panel D Back-right leg E Right panel F Front-right leg G Gas cylinder support H Bottom beam I Door J Front-left leg K Left panel L Upper beam M Back-left leg N Weather cover O Door handle P Foot glider Q Lava rock (13.
PAGE 6
ASSEMBLY INSTRUCTIONS NOTE: Tool Required for Assembly: phillips screw driver ( NOT included) 1. Carefully unpack all parts from the box, compare parts with package content listed above, make sure all parts are present before beginning assembly of product. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. 2.
PAGE 7
Hardware Used: AA Bolt (M6 x 15) BB Washer (M6) CC Hex screw driver CC AA BB x4 x4 x1 D F E Figure 4 5. Attach upper beam (L) to front-left Leg (J) and front-right leg (F) with bolt (AA) and washer (BB) using the hex screw driver (CC). Attach bottom beam (L) to front-left leg (J) and front-right leg (F) with bolt (AA) and washer (BB) using hex screw driver (CC), (see Figure 5). CC AA BB NOTE: DO NOT tighten the screws completely.
PAGE 8
7. Attach door (I) to upper beam (L) and bottom beam (H) with bolt (AA) and washer (BB) using hex screw driver (CC), (see Figure 7). NOTE: DO NOT tighten the screws completely. Hardware Used: AA Bolt (M6 x 15) BB Washer (M6) CC Hex screw driver CC AA BB x2 x2 x1 L BB I H Figure 7 8. Attach door handle (O) with bolt (DD), then use phillips screw driver (not included) to screw tightly (see Figure 8). NOTE: DO NOT tighten the other screws completely. Hardware Used: DD Bolt (M4 x 25) DD x1 O Figure 8 9.
PAGE 9
10. Put lava rock (P) around the burner, then remove the label from pilot box (see Figure 10). A gas fire pit requires 13.2 lbs lava rock. NOTE: DO NOT completely cover the burner element or block the pilot box with the lava rocks. When the first use, preheat the lava rocks for 15 minutes to burn out the impurities and air in the natural lava rocks. WARNING: keep children away during assembly, as this item contains lava rock, which are small pieces and can be swallowed by children.
PAGE 10
STOP NATURAL GAS CONVERSION STOP Natural gas conversion must be performed only by natural gas provider or service company. 1. Disconnect the propane hose from the gas valve (see Figure 13). gas valve propane hose 2. Figure 13 Unscrew and disconnect the propane orifice from the bellows (see Figure 14). Propane orifice (2.21 mm diameter size) is painted with red mark. propane orifice propane orifice bellows bellows Figure 14 3.
PAGE 11
4. Connect the natural gas hose with the gas valve by screwing clockwise tightly (see Figure 16). Plug the natural gas fixture into the natrual gas supply piping system (see Figure 17). gas valve natural gas fixture natural gas supply piping system natural gas hose Figure 16 5. Figure 17 Stick and cover the conversion label onto the propane rating plate (see Figure 18). Serial Number: CAUTION: This appliance has been converted to use natural gas. Propane orifice dia2.21mm, natural gas orifice dia4.
PAGE 12
BATTERY Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignitor module located on the control panel to access the battery compartment. The ignitor module requires one AAA size battery (See Figure 19), BATTERY IS NOT INCLUDED. WARNING: 1. Please observe proper polarity and use the correct battery type when placing or replacing the battery. Improper installation could result in ignition failure. 2.
PAGE 13
gas valve-hose connection (Figure 22) inlet tube-bellows connection (Figure 23) To perform a leak test: 1. Make 2~3 oz. of leak solution by mixing one part liquid dishwashing detergent and three parts water. Noted: make sure control knob is “OFF”. 2. Apply several drops of solution where the cylinder attaches to regulator (see Figure 20), inspect the solution at the connection looking for bubbles. If NO bubbles appear, the connection is secure.
PAGE 14
Observe Flame Height When Lit: The burner will display blue and yellow flames. These flames should be a blue / yellow color between 1~2 in. height (see Figure 25). These flames should not be yellow or produce thick smoke. This would indicate an obstruction of airflow through the burners. The flames should be blue with straight yellow tops.
PAGE 15
REPLACEMENT PARTS LIST NO PART# DESCRIPTION 01 CLTN-L Lid 02 CLTN-SQTTA Table top 03 CLTN-RP Right panel 04 CLTN-LP Left panel 05 CLTN-DR Door 06 CLTN-BP Back panel 07 CLTN-FRLG Front-right leg 08 CLTN-BRLG Back-right leg 09 CLTN-FLLG Front-left leg 10 CLTN-BLLG Back-left leg 11 CLTN-UPBM Upper beam 12 CLTN-BTBM Bottom beam 13 CLTN-GCSPT Gas cylinder support 14 CLTN-FOOTGD Foot glider 15 CLTN-HDL Handle assembly 16 CLTN-THRMCPL Thermocouple 17 CLTN-PLSELT
PAGE 16
WARRANTY Firepits Burner, steel fire pit bowl, all mechanical parts and fittings to control panel and burner assembly are warranted for a period of one (1) year from original date of purchase, against defects in material and or workmanship. Rust is not covered. Frames Frames are warranted to be free from defects in materials and workmanship for a period of one (1) year. Damage to frames or welds due to improper assembly or exposure to water and sub-freezing temperatures, is not covered.