Cottage 34 in Square Gas Fire Pit MODEL#: FW-CTGSQFP ANSI Z21.97/CSA 2.41-2014 Outdoor Decorative Gas Appliances Installer: Leave these instructions with consumer. Consumer: Keep these instructions for further reference.
IMPORTANT SAFETY INFORMATION 1. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1●NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable. 2.
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S. Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable. 2. The LP-gas supply cylinder to be used must have a listed overfilling prevention device (See Figure 1). 3.
PACKAGE CONTENTS P PART Q DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY A Tabel top assembly 1 K Bottom beam 1 B Right panel 1 L Gas cylinder support 1 C Left panel 1 M Foot glider 4 D Door 1 N Weather cover 1 E Back panel 1 O Handle 1 F Front-right leg 1 P Lava rock G Back-right leg 1 Q Natural gas orifice 1 H Front-left leg 1 AA Bolt (M6 x 15) 30 I Back-left leg 1 BB Washer (M6) 30 J Upper beam 1 CC Hex screw driver 1 2 pkg
ILLUSTRATED PARTS LIST A D Table top assembly Door B Right panel C Left panel E Back panel F Front-left leg I Back-left leg Gas cylinder support Front-right leg G Back-right leg H J Upper beam K Bottom beam L M Foot glider N Weather cover O Handle Q Natural gas orifice AA Bolt (M6 x 15) P BB Lava rock Wahser CC Hex screw driver
ASSEMBLY INSTRUCTIONS Note: Tool Required for Assembly: Phillips screw driver ( NOT included) 1. Carefully unpack all parts from the box, compare parts with package content listed above, make sure all parts are present before beginning assembly of product. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. 2.
Hardware Used: AA Bolt (M6 x 15) BB Washer (M6) CC Hex screw driver x 8 x8 x1 Figure 4 5. Attach the Gas Cylinder Support (L) to the Right Panel (B) and the Left Panel (C) with Bolt (AA) and Washer (BB) by using the Hex Screw Driver (CC), (see Figure 5). NOTE: DO NOT tighten the screws completely. Hardware Used: AA Bolt (M6 x 15) BB Washer (M6) CC Hex screw driver x 4 x4 x1 Figure 5 6.
7. Unpack the Handle (O) package, loosen the screw, attach the Handle (O) to the Door (D) by using the phillips screw driver, then screw it tightly, (see Figure 7). NOTE: DO NOT tighten the screws completely. Figure 7 8. Attach the assembled base to the Table Top Assembly (A) with Bolt (AA) and Washer (BB) by using the Hex Screw Driver (CC). Make sure the control panel just covers up the notch on the Right Panel (B), (see Figure 8). Then tighten all the screws completely.
10. Open the door, place the gas cylinder into the Gas Cylinder Support (L), connect the regulator, screw the black handle clockwise to tighten, turn the black handle counterclockwise to remove. The hose must point down. The knob on the control panel is turned all the way to the “OFF” position when the fire pit is NOT in use (see Figure 10). black handle Figure 10 11.
STOP NATURAL GAS CONVERSION STOP Natural gas conversion must be performed only by natural gas provider or service company. 1. Disconnect the propane hose from the gas valve (see Figure 12). gas valve propane hose Figure 12 2. Unscrew and disconnect the propane orifice from the bellows (see Figure 13). Propane orifice (dia2.09mm size) is painted with red mark. propane orifice bellows propane orifice bellows Figure 13 3.
4. Connect the natural gas hose with the gas valve by screwing clockwise tightly (see Figure 15). Plug the natural gas fixture into the natrual gas supply piping system (see Figure 16). gas valve natrual gas fixture natrual gas supply piping system natural gas hose Figure 15 Figure 16 5. Stick the conversion label onto the propane rating plate (see Figure 17).
BATTERY Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignitor module located on the control panel to access the battery compartment. The ignitor module requires one AAA size battery (See Figure 18). WARNING: 1. Please observe proper polarity and use the correct battery type when placing or replacing the battery. Improper installation could result in ignition failure. 2.
gas valve-hose connection (Figure 21) inlet tube-bellows connection (Figure 22) To perform a leak test: 1. Make 2~3 oz. of leak solution by mixing one part liquid dishwashing detergent and three parts water. Noted: make sure control knob is “OFF”. 2. Apply several drops of solution where the cylinder attaches to regulator (see Figure 19), inspect the solution at the connection looking for bubbles. If NO bubbles appear, the connection is secure.
Observe Flame Height When Lit: Flame should be a blue / yellow color between 1~2 in. height (see Figure 24). Bad Good Figure 24 CARE AND MAINTENANCE To enjoy the outstanding performance from your fire pit, make sure you perform the following activities on a regular basis: 1. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. 2. While cleaning the fire pit, make sure to keep the area around the burner dry at all times. DO NOT submerge the control valve assembly.
REPLACEMENT PARTS LIST NO 01 PART# EFP-RDTTA DESCRIPTION Table top assembly 02 EFP-RP Right panel 03 EFP-LP Left panel 04 EFP-DR Door 05 06 EFP-BP EFP-FRLG Back panel Front-right leg 07 08 EFP-BRLG EFP-FLLG Back-right leg Front-left leg 09 EFP-BLLG Back-left leg 10 11 EFP-UPBM EFP-BTBM Upper beam Bottom beam 12 EFP-GCSPT Gas cylinder support 13 14 EFP-FOOTGD EFP-HDL Foot glider Handle 15 EFP-THRMCPL Thermocouple 16 17 18 EFP-PLSELT EFP-CNNB EFP-HRDPK Pulse Ignition Knob Ha
WARRANTY Firepits Burner, steel fire pit bowl, all mechanical parts and fittings to control panel and burner assembly, and all fire pit tops that are not cast aluminum are warranted for a period of one (1) year from original date of purchase, against defects in material and or workmanship. Rust is not covered. Frames Frames are warranted to be free from defects in materials and workmanship for a period of one (1) year.