Instruction Manual

LED Outdoor Sconce Luminaires Model # KNXW061010L30D2XX
Surface Mount
120-277VAC / 60Hz
Page 1 of 1 8061092 R0
Safety Precautions
 Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in
potentially fatal electric shock and/or property damage.
 It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.
 Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a wet or damp surface or in water.
 This fixture is designed for use in a 120-277VAC, 60Hz fused circuit and can be used in conjunction with 0-10V dimmers.
 To reduce the risk of electrical shock, and to assure proper operation, this fixture must be adequately grounded. To accomplish proper grounding, there must be a
separate ground wire (green) contact between this fixture and the ground connection of your main power supply panel.
 This fixture is intended to be used for general indoor or outdoor lighting in dry, damp or wet locations. For wet location, fixture must be mounted 48” above ground level.
 Disclaimer
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005
(B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modifications to this fixture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Assembly Instructions
1. Preparing for installation.
A. Disconnect electrical power before installing or servicing any part of
this fixture.
B. Remove fixture from box. Separate contents of parts bag.
C. Remove wall plate (1) from the fixture (3).
D. Install wall plate (1) to junction box (not provided) with narrow end
pointing downward and secure with two #8-32 screws (2).
2. Wiring.
All wiring must take place inside junction box.
Caution: Make sure power is off at fuse or circuit breaker box. Check power
wires for damage or scrapes. If power supply wires are within three inches of
driver, use wire suitable for at least 90C (194F). Note: Most dwellings built
before 1985 have supply wire rated to 60C. Consult a qualified electrician
before installing.
A. This unit will not operate properly unless connected to a “grounded”
electrical circuit. Electrical shock, over-heating, low or no light output,
and shortened LED life can result if proper grounding is not done.
B. Make all wire connections to appropriate wire. Secure with wire nuts
(supplied).
C. Connect green wire from the fixture to the ground power source green
wire.
D. For Non-dimming. Fixture will operate normally w/o a connection to a
dimmer. Connect white fixture lead to white (N) wire from supply power
source. Connect black fixture lead to black (L) wire from supply power
source. Make sure to cap gray and purple wires separately to prevent
shorting.
E. For 0-10V dimming. Connect gray wire from the fixture to the dimmer
source gray wire. Connect purple wire from the fixture to the dimmer
source purple wire. Connect white fixture lead to white (N) wire from
supply power source. Connect black fixture lead to black (L) wire from supply power source.
F. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire connectors. Tuck all
connections neatly into the junction box.
3. Fixture mounting.
A. Install fixture (3) to the wall plate (1) and secure with two #4-40 screws (4).
4. For Wet application.
A. Place a small bead of silicone or water proof caulk (not included) around the fixture (3) where it contacts with the surface of wall apply on top and two sides, but
not on bottom.
5. Restore power at fuse or circuit breaker box.
Limited Factory Warranty
AFX Inc. hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years
from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover failure due to improper
installation, misuse, mishandling or damage incurred in transit.