Instructions / Assembly

ManualsBrandsAFX ManualsLightingMagnus 7 in. 3 Light Black Vanity Light with Acrylic Shade

E26 Bulb Indoor Luminaires

Vanity - Wall Mount

120VAC / 60Hz

Page 1 of 1 8061422 R0

Part #: MGNV2105MBxx

Part #:

Limited Factory Warranty

AFX Inc. hereby warrants that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions

for a period of 5 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or

components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit. For questions, please class AFX 1-

800-873-2326.

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in

potentially fatal electric shock and/or property damage.

 It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a wet or damp surface or in water.

 This fixture is designed for use in a 120VAC / 60Hz circuit.

 Make sure that the power source conforms to the requirements of the fixture. (See labels on the fixture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this fixture must be adequately grounded. To accomplish proper grounding, there must be a

separate ground wire (green) contact between this fixture and the ground connection of your main power supply panel.

 This fixture is intended to be used for general indoor lighting in dry or damp locations.

Assembly Instructions

Step 1 – Preparing for installation

A. Disconnect electrical power at fuse or circuit breaker box before installing or

servicing any part of this fixture.

B. Carefully remove the fixture from the carton, remove components from hardware kit.

C. Install mounting bracket (1) to junction box (not included) using two screws (2) to

secure it.

Wiring – All wiring must take place inside junction box (not included)

Caution: Make sure power is off at fuse or circuit breaker box. Check power wires

for damage or scrapes. Use wire suitable for at least 90°C (194°F). Note: Most

dwellings built before 1985 have supply wire rated to 60°C. Consult a qualified

electrician to ensure correct branch circuit conductor before installing.

Step 2 – Wiring fixture

A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

B. Connect the green wire from the fixture to the supply source ground wire.

C. Connect the black wire from the fixture to the black (L) wire from supply power

source.

D. Connect the white wire from the fixture to the white (N) wire from supply power

source.

E. Do not mix wires. Pull on each wire lead to make sure connections are secure.

Make certain no bare wires are exposed outside of wire connectors. Tuck all

connections neatly into the junction box.

Step 3 – Mounting

A. Install the fixture (3) by placing it over the mounting bracket (1) and use two screws

(4) to secure it.

Step 4 – Lamping

A. Install three medium base bulbs (E26, 60W max. – not included) into each socket and turn clockwise

until secured.

Step 5 – Restore power at fuse or circuit breaker box

Summary of content (1 pages)

PAGE 1
E26 Bulb Indoor Luminaires Vanity - Wall Mount 120VAC / 60Hz Part #: MGNV2105MBxx Part #: Safety Precautions        Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in potentially fatal electric shock and/or property damage. It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.