User Manual

ManualsBrandsAg Leader ManualsEquipmentInSight Spinner Spreader

Part No. 2002831-39 Rev. D

Granular Spinner Spreader Module

Quick Reference Sheet

Section 1: Configuration Procedure

The following procedure describes the complete process of configuring a granular

spinner bed control system. To begin, go to the Application Setup Configuration Tab,

press the Add button, and the Operating Configuration Wizard appears.

Note: In order for you to use this configuration at the Run screen, you must

configure a vehicle, implement, controller and product(s). For more information on how

to configure these, consult the InSight User Manual.

Granular Spinner Spreader Configuration

STEPS ACTION

1 Select Equipment Configuration Type

Note: This step will only be present if the Multi-product feature has been

unlocked in the display. Skip ahead to Step 2 if you have not purchased a

Multi-product unlock code.

Select Single Product Application from the drop-down list, then press Next

to continue.

2 Select Vehicle

Use the drop-down list to select an existing vehicle from the Vehicle list, or

press New to launch the Vehicle Wizard to create a new vehicle.

Note: If you do not need to create a new vehicle, skip ahead to Select

Operating Mode in Step 7 on page 2.

3 Create New Vehicle

If you pressed New, the Vehicle Setup Wizard appears.

 Self-Propelled Spreader operators should select Self-Propelled

Spreader from the Vehicle Type list box. Select Spinner from the

Spreader Type list box; then press Next to continue.

 Other operators should select another vehicle type under the Vehicle

Type list.

4 Enter Vehicle Information

Use the on-screen keyboard to enter names for the Vehicle Make and Model.

Press Next to continue.

Summary of content (14 pages)

PAGE 1
Granular Spinner Spreader Module Quick Reference Sheet Section 1: Configuration Procedure The following procedure describes the complete process of configuring a granular spinner bed control system. To begin, go to the Application Setup Configuration Tab, press the Add button, and the Operating Configuration Wizard appears. Note: In order for you to use this configuration at the Run screen, you must configure a vehicle, implement, controller and product(s).
PAGE 2
Granular Spinner Spreader Configuration (continued) STEPS ACTION 5 Enter Vehicle Name The display combines the Vehicle Make and Model for use as a Vehicle Name. Use the on-screen keyboard to edit the vehicle name if desired. Press Finish to complete Vehicle setup and continue with the configuration process. If you selected Self-Propelled Spreader in Step 3 on page 1, then skip ahead to Step 7. If you selected another type of vehicle, then continue below.
PAGE 3
Granular Spinner Spreader Configuration (continued) 9 Select Controller (for Spinner Spreaders or Stepper Spreader Control) If you chose to enter a new controller in Step 8, the Controller Setup Wizard appears. Select DirectCommand from the Device drop-down list box.
PAGE 4
Granular Spinner Spreader Configuration (continued) 14 Enter Container Name and Location Use the keypad to enter a Container Name, and use the drop-down menu to enter a Container Location. Press Finish and you will return to the Operating Configuration Wizard. 15 Select Ground Speed Source The Operating Configuration Wizard appears. Select Primary and Backup speed inputs from the drop-down menus. Press Next to continue.
PAGE 5
Section 2: Standard Spreader Setup Part No. 2002831-39 Rev.
PAGE 6
Section 3: Standard Stepper Setup Part No. 2002831-39 Rev.
PAGE 7
Section 4: Setup Menu Part No. 2002831-39 Rev.
PAGE 8
Section 5: Direct Command Menu Tree Part No. 2002831-39 Rev.
PAGE 9
Section 6: Run Screen Functionality Part No. 2002831-39 Rev.
PAGE 10
Section 7: Key Settings/Functionality Spinner Spreader Application Rate Control Tab The Application tab for spinner spreader control has several buttons and status display areas that are specific to granular product control. This table outlines the details of these controls. Press to display the Spreader Control window and settings.
PAGE 11
Section 8: Controller Settings These settings are shown in Controller Settings window, accessed via the Controller Settings button on the Controller Tab. These settings appear on the Channel Tab. Controller Settings - Channel Tab Setting Name Default Setting Shaft Speed Cal Control Valve Configuration 180 Calibration number representing the pulses that equal one revolution of the rate control metering system.
PAGE 12
Section 8: Controller Settings (on Spinner Tab) The settings shown below appear on the Spinner Tab. Controller Settings – Spinner Tab Setting Name Default Setting Description/characteristics The number of pulses that are generated by the sensor during one revolution of the spinner dish. Fan Speed Cal 4 PWM Frequency 100 The frequency that the PWM control valve is pulsed at. Settings can be found from the manufacturer of the valve. Typical settings range from 100-125 Hz.
PAGE 13
Section 9: Spinner Spreader Control Settings – from Run Screen These settings are shown in Controller Settings window, accessed via the Spinner Control button on the Run screen. Each of these settings described below must be set for each individual Product Channel (bin). Changing any of these settings in the display does not make the needed adjustments on the product applicator. Setting value and physical setting on the spinner bed must be verified for correctness prior to any product application.
PAGE 14
Part No. 2002831-39 Rev.