Quick Reference Sheets Owner manual

ManualsBrandsAg Leader ManualsEquipmentPFadvantage Hiniker 8605 Controller

PF3000 and PF3000 Pro – Application Rate Mode - Menu Tree for Hiniker 8605 – March 2002

Menu Key

FIELD LOAD

OPTIONS SHOW MAP

CAL SETUP

DIAG

Press Menu Key to switch between Main Menu keys

OPTIONS

LIGHTBARMARKS

NAVIGATE

BOUNDARY

GRID

AREA PT

CLR/STOP

ADD/STRT

PAUSE

RESET

SET B

SET A

FIELD

VIEW

CONFIG

[Create or change field and name field

functions. Active configuration for

field displayed.]

[Set active configuration and active

tgt prescription file.]

ACTIVE

ON/OFF

EDIT

TGT FILE

[Select and accept new tgt

rescription file.]

VIEW

INFO

LOAD

SHOW MAP

[Create or change load and

name load functions.]

[Splits screen and shows On

Screen Map on left side.

Press HIDE MAP key to

return to full screen. ]

Press to

ause

guidance

when filling

applicator.

Drive back

to swath and

ress

RESUME

key.

Press at every

corner of field to

calculate field

area. Must have

“Field Area”

displayed on

main screen to

see area.

Used for

Headlands.

See Lightbar

Manual.

Used for

Headlands.

See Lightbar

Manual.

[Screen displays field, product, units/ac and default

rate stored in tgt file.]

Press at

eginning o

guidance

reference

ass.

Press at end

of guidance

reference

ass. When

using curve

attern,

ress at end

of every

ass.

Press to

reset

guidance

and area

oints to

start a new

field.

Revision 1 1 of 4 P.N. 2002831-26

Summary of content (4 pages)

PAGE 1
PF3000 and PF3000 Pro – Application Rate Mode - Menu Tree for Hiniker 8605 – March 2002 Menu Key FIELD LOAD SHOW MAP CAL SETUP DIAG OPTIONS Press Menu Key to switch between Main Menu keys FIELD [Create or change field and name field functions. Active configuration for field displayed.] LOAD SHOW MAP [Create or change load and name load functions.] [Splits screen and shows On Screen Map on left side. Press HIDE MAP key to return to full screen.
PAGE 2
PF3000 and PF3000 Pro – Application Rate Mode - Menu Tree for Hiniker 8605 – March 2002 Menu Key FIELD LOAD SHOW MAP CAL SETUP DIAG OPTIONS Press Menu Key to switch between Main Menu keys CAL AREA SETUP APP RATE CONFIG DISTANCE MARKS [Radar calibration screen] Settings Logging device Logging interval Log file [Screen Displays all product/controller configurations] EDIT SETTINGS CARD CREATE NEW DELETE [To erase files, press SHOW ALL FILES key, select file, press FILE OPTIONS key and press
PAGE 3
PF3000 and PF3000 Pro – Quick Reference Setup Instructions for Hiniker 8605 controllers – March 2002 Note: These instructions pertain to PF firmware versions 4.00 or higher. Connect Hiniker Serial Cable (pn 2000951) to port3 of PF. Settings for Hiniker 8605 Controllers 1. 2. Press SETUP key. Press APP RATE CONFIG key. Press CREATE NEW key. Set the following: Controller Make: Set to HINIKER. Controller Model: Set to 8605. Product: Press EDIT key.
PAGE 4
PF3000 and PF3000 Pro – Quick Reference Setup Instructions for Hiniker 8605 controllers – March 2002 Note: To check the software version in the 8605 console, press the Menu key and select exit. Using a target file and setting an automatic rate a) Press Left Arrow key to highlight “auto” (“a” if viewing on screen map). b) You must have a target file (.tgt) selected for the field, otherwise the PF will not control the rate of the Hiniker. Refer to step 4 on other side on how to set the Target File.