AGA CITY24 (Gas Top Burners) WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT DO YOU DO IF YOU SMELL GAS . Do not try to light any appliance. . Do not touch any electrical switch . Do not use any phone in your building. . Immediately call your gas supplier from a neighbors phone.
CONTENTS SECTION PAGE Product Safety 3 General Notes 4 Health and Safety 4 General Installation Requirements 4 Installation 5 Technical Data 6 Removal From Pallet and Cooker Installation 7-8 Range Dimensions - AGA City24 (Gas Top Burners) 9 Clearances 10 - 11 Location 12 Connection to Power Supply 13 Mains Cable Routing 14 Connecting to Gas 15 Cooker Stability 16 - 17 Pressure Testing 17 Assembly of Burners 18 To Adjust Pan
PRODUCT SAFETY MEANING/DESCRIPTION SYMBOL SIGNIFICATION/DESCRIPTION WARNING/CAUTION AVERTISSEMENT An appropriate safety instruction should be followed or caution to a potential hazard exists. Une consigne de sécurité appropriée doivent être suivies ou garde d’un danger potentiel exists. DANGEROUS VOLTAGE TENSION DANGEREUSE To indicate hazards arising from dangerous voltages. Pour indiquer les dangers résultant des tensions dangereuses.
GENERAL NOTES NOTE: THESE INSTALLATION INSTRUCTIONS SHOULD BE LEFT WITH THE RANGE AND THE USER TO RETAIN FOR FUTURE REFERENCE. HEALTH AND SAFETY Consumer Protection As responsible manufacturers we take care to make sure that our products are designed and constructed to meet the required safety standards when properly installed and used.
INSTALLATION CAUTION: THIS INSTALLATION MUST CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE; ANSI Z223.1 / NFPA 54 OR, IN CANADA, THE NATURAL GAS AND PROPANE INSTALLATION CODE CSA B149.1 AND NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (IN CANADA CAN/CGA-B149) AND ONLY USED IN A WELL VENTILATED SPACE. READ THESE INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE.
TECHNICAL DATA GAS TOP BURNERS This appliance is supplied set for Natural Gas (NG) at a pressure of 4” WC. It must be converted to run on LP Gas (Propane) at a pressure of 10” WC. NATURAL GAS L.H.F. R.H.R. L.H.R. R.H.F. BURNER TYPE ULTRA-RAPID RAPID SEMI-RAPID SEMI-RAPID (WOK) MAXIMUM HEAT INPUT 3.5 kW 3.1 kW 1.8 kW 1.
REMOVAL FROM PALLET AND COOKER INSTALLATION Removing of transit brackets - Unscrew 4 screws and remove brackets, from front and two screws from rear. NOTE: Care must be taken not to trap mains cable. MAINS CABLE Appliance to be removed from rear of pallet only. Recess provided for suitable sack truck. Appliance to be secured to sack truck with suitable straps (shaded area) Fig. 1 DESN 517176 Fig. 2 Once appliance is in position in kitchen, remove sack truck and straps.
REMOVAL FROM PALLET AND COOKER INSTALLATION Levelling of appliance - Use 1/2” (13mm) socket to adjust wheel mechanism for FINE adjustment on both sides at rear of the appliance. Appliance can now be pushed back on its wheels into desired position. NOTE: Care must be taken not to trap mains cable. Using a 1/2” (13mm) open end spanner, feet can be adjusted at front to make FINE adjustments to the front of the appliance and to provide a brake for the wheels.
RANGE DIMENSIONS - AGA CITY24 (GAS TOP BURNERS) Fig.
CLEARANCES Side Clearances If you are installing a AGA City24 in a new kitchen or have the opportunity to set the width between kitchen or units, it is advisable to include an additional small gap each side of 1/8” (3mm) to assist with installation and prevent damage when moving the product. A 15/64” (6mm) additional width clearance should also be provided if the range is to go into a brick recess, to allow for the wall being out of square.
Combustible Rear Walls Since this range can be used continuously, please take note of the IMPORTANT INSTRUCTIONS. Where the rear wall is constructed of combustible materials (such as all-timber or stud wall partitions and batoned plasterboard) these will require special wall heat protection measures. Non-combustible insulation board as a protective cladding can be used behind the range of at least 5/8” (15mm) thick, such as Monolux or equivalent. This should be taken up to hotplate level. See Fig. 9A.
LOCATION Combustible side wall clearance above the gas top plate shall be greater than 3” (76mm). Surfaces over the top of the range must not be closer than 28” (711mm) and must not exceed 13” (330mm) in depth. The vent slot in the back of the top plate must not be obstructed. Note: It is essential that the supply cable is routed away from any hot surfaces i.e. flue pipes. In the interests of safety, due consideration must be given to the protection of the electric cable to the unit.
CONNECTION TO THE POWER SUPPLY Electric Shock Hazard Rating Plate is located behind removable plinth, see Fig. 11. Electrical Grounding is required on this appliance. DO NOT connect to the electrical supply until the appliance is permanently grounded. This appliance must be connected to a grounded metallic permanent supply or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. Failure to follow these instructions could result in death or serious injury.
MAINS CABLE ROUTING Fig. 10 Fig. 10A SECURE MAINS CABLE USING ‘P’ CLIPS FOR LEFT HAND OR RIGHT HAND CABLE MANAGEMENT DESN 516918 POWER CORD 50A/250V 12500W RATED FITTED WITH NEMA 14-50P RIGHT ANGLED PLUG (MATCHING RECEPTACLE 14-50R) UL OR CSA APPROVED DESN 516919 RATING PLATE LOCATED BEHIND PLINTH THE MAINS SUPPLY MUST BE WITHIN THE ZONES SHOWN IF A RECESSED RANGE CONNECTION IS TO BE USED BEHIND THE RANGE WITHIN THE HATCHED AREA. ALLOW A 3/16”(5mm) GAP AT REAR OF RANGE Fig.
CONNECTING TO GAS CAUTION: ENSURE THAT THE RANGE IS ISOLATED FROM ELECTRIC SUPPLY. The range can be installed with an approved flexible connection. Supply piping should not be less than 3/8” I/D flexiline. Connection is made to the 1/2” NPT female thread located on the rear right hand side of the range. PRESSURE TEST POINT REGULATOR GAS INLET 1/2” NPT Fig. 12 DESN 517234 The gas flexiline connector provided, must be fitted to the wall in the shaded area dimensioned in Fig. 14.
COOKER STABILITY A safety chain must be anchored firmly to the wall and cooker to prevent the flexible hose from straining, when the cooker is withdrawn for servicing. When fitting a safety chain refer to Fig. 13. Fig. 13 DESN 517192 If disconnection of the restraining chain is necessary, then ensure restraining chain is re-attached as appliance is nn relocated in its original position to avoid serious injury or fatality.
POSITION OF GAS CONNECTOR ON WALL (located in shaded area) IMPORTANT: THE GAS SUPPLY CONNECTION AT THE WALL MUST NOT PROJECT OUT FROM THE WALL BY MORE THAN 1 3/4” (45mm), SO THAT IT DOES NOT FOUL WITH THE BACK OF THE RANGE. LOCATION AREA FLEXILINE CONNECTOR Fig.14 DESN 517235 PRESSURE TESTING The pressure test point is situated just below hotplate level on the rear right hand side of the range. (See Fig. 12). The maximum gas inlet pressure to the appliance must not exceed 10” w.g.
ASSEMBLY OF BURNERS FITTING OF BURNER CAP - RAPID AND SEMI-RAPID BURNERS PLACE BURNER CAP OVER RETAINING LUGS, THEN TURN CAP CLOCKWISE TO LOCK INTO POSITION. BURNER CAP RETAINING LUGS Fig. 15A DESN 511617 ASSEMBLY OF RAPID AND SEMI-RAPID BURNERS Fig. 15B DESN 513513 WOK BURNER Fig.
TO ADJUST PAN SUPPORT LEVEL 1. 2. 3. 4. Loosen retaining nut using 1/4” (8mm) spanner (See Fig. 16). To prevent rocking adjust the pan support foot using 1/8” (2.5mm) allen key. Check pan support is level with opposing pan supports. Retighten retaining nut. DESN 517187 Fig.
CONTROL KNOB AND HANDRAIL CONNECTION RIGHT HAND REAR CONTROL KNOB RIGHT HAND FRONT CONTROL KNOB LEFT HAND REAR CONTROL KNOB LEFT HAND FRONT CONTROL KNOB OVEN CONTROL KNOB Fig. 17 DESN 517186 Control Knob and Bezel Location Ensure control knobs and bezels are located onto spindles correctly, as shown in Fig 17. Handrail Location Locate handrail onto spindle, lock into position with grub screws (located on the underside of the bracket).
WIRING DIAGRAM Fig.
AGA CITY24 (GAS TOP BURNER) CHECKLIST SERIAL No. Tick Box l Check pan supports and gas hotplate burners are correctly fitted. l Check gas pressure is correct. l Check fit of control knobs and bezels. l Check hotplate burner ignition. l Check oven door seals, adjust door alignment if necessary. Ensure all plastic film is removed from the inside of the oven doors. l Turn on roasting and slow cook oven.
For further advice or information contact your local AGA Specialist With AGA Marvel’s policy of continuous product improvement, the Company reserves the right to change specifications and make modifications to the appliance described and illustrated at any time. Supplied by AGA Marvel 1260 E. Van Deinse St. Greenville, MI 48838 Business (616) 754-5601 Fax (616) 754-9690 Toll Free Telephone 800-223-3900 www.agamarvel.