AGA ELECTRIC - AIMS EC3 COOKER Installation Instructions REMEMBER: when replacing a part on this appliance, use only spare parts that you can be assured conform to the safety and performance specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Aga.
CONTENTS SECTION PAGE CONSUMER PROTECTION 3 HEALTH & SAFETY 3 INSTALLATION 4 TECHNICAL DATA - AGA EC3 5 BAKING OVEN BAFFLE PLATE 6 ELECTRICAL 6 ELECTRICAL TEST PROCEDURE 6 WIRING DIAGRAM 7 TO TEST THE AIMS CONTROL HANDSET 7 MAINS CABLE & GUIDE TUBE ASSY 8 ELEMENTS AND ELECTRICAL HOUSING PARTS ASSY 9 OVEN VENT PIPE CONNECTION OPTIONS 9 OVEN THERMOCOUPLE 10 OVEN VENTING SYSTEMS 11 - 12 AIMS HANDSET 13 INSTRUCTIONS 14 2
HEALTH & SAFETY Consumer Protection As responsible manufacturers we take care to make sure that our products are designed and constructed to meet the required safety standards when properly installed and used. PLEASE READ THE ACCOMPANYING WARRANTY. Any alteration that is not approved by Aga could invalidate the approval of the appliance, operation of the warranty and could also affect your statutory rights.
INSTALLATION With specific exceptions, the installing of any type of Aga cooker is subject to the respective directions contained in current issue of the Building Regulations. In addition, planning permission may need to be obtained, which should be applied for separately. The complete cooker is floor-mounted and the space in which the appliance is to be fitted must have the following minimum dimensions:A minimum clearance of 60mm is required above the raised insulating cover handle.
TECHNICAL DATA - AGA EC3 Fig. 1 DESN 514194 A B C D F G H mm 987 889 851 679 1330 756 1125 K 3 L M N R T V W X Y Z 698 484 816 116 52 790 873 55 699 662 * THIS HOLE IF REQUIRED FOR OVEN VENT PIPE IS TO BE CUT ON SITE IN THE LEFT OR RIGHT HAND SIDE PANEL. PLEASE NOTE: SIDE CLEARANCE DIMENSION R IS ALSO REQUIRED ON THE LH SIDE FOR THE BAKING OVEN DOOR.
BAKING OVEN BAFFLE PLATE A metal plate which is provided in the Aga pack MUST be positioned on the top runners of the Baking Oven. Slide the plate in fully, until it makes contact with the back of the oven. This baffle is a permanent part of the Baking Oven, to regulate the oven temperature. ELECTRICAL WARNING: THIS APPLIANCE MUST BE EARTHED. THIS APPLIANCE IS DESIGNED FOR THE VOLTAGE STATED ON THE RATING PLATE, WHICH IS SITUATED BEHIND THE UPPER LEFT HAND DOOR.
Fig. 2 TO TEST THE AIMS CONTROL HANDSET Fig. 3 Press the fan button on the handset, the vent fan symbol should show on the handset screen. The oven vent fan should operate and the fan oven neon on the control panel should illuminate. Press the fan button again and the fan should go off.
MAINS CABLE AND GUIDE TUBE ASSEMBLY Fig.
ELEMENTS AND ELECTRICAL HOUSING PARTS ASSEMBLY Fig. 5 DESN 514245 OVEN VENT PIPE CONNECTION OPTIONS Fig.
OVEN THERMOCOUPLE NOTE: On AIMS controlled cookers the thermostat phial (probe) has been replaced by an oven thermocouple sensor, which is fitted to the PCB on the controls chassis. (See Fig. 2). 1. Feed the thermocouple sensor through the guide tube into the Roasting oven. 2. Fit the thermocouple sensor to the support plate so that the sensing tip is as shown in (See Fig. 7). DO NOT OVERTIGHTEN the clamp as this may damage the sensor. Screw support plate to top of roast oven. 3.
OVEN VENTING SYSTEMS See Figs. 9, 10, 11 & 12 Pre-site visiting will have determined where and how the layout of the oven vent pipework should be designed and installed. It is then necessary to check that the pipework design and the pipework resistance are within the parameters possible. The appliance oven venting pipe can be achieved, up to a maximum length of 6 metres, through an outside wall or unused flue etc. Great care must be taken in all-timber houses.
Fig. 10 Fig. 11 DESN 515278 Fig.
AIMS HANDSET Handset can be wall mounted as described below. Remove backplate from the rear of the Handset by sliding down with hand and away from the Handset (fig 13). Select the site for the handset and use the backplate to mark the position of fixing holes. Drill 6mm dia. holes with masonry drill for the rawplugs. Use rawplugs and screws supplied to fix the backplate to the wall (fig. 14). Stick the round self adhesive label supplied to the inside of the backplate to cover the fixing screw heads.
INSTRUCTIONS Hand these instructions to the User for retention, and instruct in the safe operation of the appliance. Finally advise the User, that for continued efficient and safe operation of the appliance, it is important that adequate servicing is carried out at regular intervals recommended by the Aga Specialist.
For further advice or information contact your local Aga Specialist With Aga’s policy of continuous product improvement, the Company reserves the right to change specifications and make modifications to the appliance described and illustrated at any time Manufactured by Aga Station Road Ketley Telford Shropshire TF1 5AQ England www.aga-web.co.uk www.agacookshop.co.uk www.agalinks.
