MFN-E-A3
CONTENTS 1. Products Introduction.................................................................................................................... 3 1.1. Specifications..................................................................................................................... 3 1.2. Applications........................................................................................................................4 1.3. System Requirements..........................................................
1. Products Introduction An IP Camera is a new generation product combined with an analog camera & IP video technology. An IP camera has an analog camera’s full function, additionally it can compress and encrypt video and audio signal through internet by sending them to remote terminals with its built-in processor and web server. Via its IP address, users can use standard PC IE browser to view IP camera and monitor targets in real time, manage and store video or image.
Image Compression Format Standard M-JPEG Sensor CMOS，300,000 pixel Image Resolution Rate VGA（640x480）/QVGA（320x240） Network interface RJ-45/10-100 Base T ，802.11b/g Network protocol TCP/IP,FTP,SMTP,HTTP,UDP,DHCP,NTP,DDNS,UPNP,D NS,PPPOE Image Max Transmission Rate 30 frame/second（QVGA）, 15 frame/second（VGA） Alert control Output: 1 router（5VDC，0.
Untie the pack and check the items contained against the following list: Wireless IP Camera------------------------------------------------------------------------------1 Wi-Fi Antenna------------------------------------------------------------------------------------1 DC Power Supply--------------------------------------------------------------------------------1 CD-------------------------------------------------------------- -----------------------------------1 Manual-------------------------------------
2.1. Interface Non-extended line IP Camera Tailgate Power Supply Light: constant on when power is on Network light: constant flash when power is on which shows data transmission. Ethernet interface: RJ-45 interface. I/O interface: 1 router alarm input, accept 3, 4 two terminals (input terminal grounding, low level effective trigger); 1 router TTL control input, connect 1, 2 two terminals (1, 2 terminals short connections).
Backup: follow-up product extend interface. About GPIO alarm interface (S terminal) definition: 1# +DC12V 2# RS485（A） 3# Earth（GND） 4# IO2 （OUT PUT） 5# RS485 （B） 6# IO1 （IN PUT） GND: Ground，alarm input ground，RS485 ground RS485: RS485 control interface，left connection RS485 negative right connection RS485 positive. connect P/T decoder， support variety PTZ protocol. 2.2.
2.2.2. PPPoE Installation Under this condition, users need to set up PPPoE dialing parameter in IP Camera: input the username and password provided by ISP supplier’ offer, this will allow the IP Camera to connect to internet by dialing connects. As for setting the PPPoE dialing parameter, you can connect device to network through the first method, then write parameter to the device, or through the following third method, directly write process parameter to device. Please refer to 3.4.5.
2.2.3. IP Camera & PC connection This method does not use frequently, when you process machine write parameter or program shift, we suggest you to use the first connect network method to process the modification of machine parameter.
3. IE Browse to IP Camera After IP camera connects to PC LAN through router, you can operate on IP camera via PC, first please run the relative software in the CD kit 3.1.
address. Before external net visit IP camera, port forwarding is necessary in the senior router ,for more detail please refer to “ Port Forwarding Settings in router ”in 8.1 section. Note Note： 1. Device information indicates IP camera information. 2. When the current computer has a fixed IP, (namely non-DHCP IP), and the IP camera is used for the first time, please click automatic setup setup, so that IP address of the IP camera, gateway and DNS can be synchronous with the PC. 3..
b. Click finish 2. Open web page，you can directly click open button which is behind inner visit address or outer visit address in the search bar, also you can directly input relatively inner and outer visit address in web page address bar such as: http: //192.168.1.126 （LAN）, http: //dpvz.ipcam.hk（WAN）.
3. When the item connects to outer networking, a log-in interface will appear: Enter log in information, click OK to enter, an installation pop-up will appear, after installation is completed then you can use it. If it is blocked and requires plug-in installation by antivirus software, please remove block. Note Note:: 1. Default device account is admin，no password. 2. M series IP camera doesn’t support Firefox browser，while F series support. 3.3.
3.3.2.
3.3.3. Operation 1. Image mirror indicates a reverse image. 2. Resolution, mode, brightness, contrast default setting are: 320*240、50HZ、6、4， mode is mainly for the adjustment of Light strength, please adjust to 60HZ when light is poor or in dark. 3. There are 3 browse modes in IE mode: visitor, operator, administrator. The authority of administrator is the highest. log in as different authorities, the operation will be different. Regarding to 3 user authorities, please refer to 3.4.4.
to finish setting, please click OK. If system indicates to restart (as right photo), please single click yes (Y), and then enter again. 3.4.1. Device Information The device information includes the above interfaces, device serial number （MAC）、device system firmware version, device application firmware version. 3.4.2. Device Name Settings Here the table displays camera name, such as the name search on search bar, the name following mentioned as multiple channels equipments setting and so on. 3.4.3.
You can adjust time via NTP server or PC in this table. 3.4.4. Device User Settings User can proceed with setting according to the interface as below. The system is available for administrator, operator, visitor whose authority are listed in order.. Note: At least one administrator is needed for the device; 3.4.5. Basic Network Settings This sector is for DHCP and IP configuration.
Referring to the wireless networking setting, there are 5 security modes: None, WEP, WPA Personal（TKIP, WPA Personal（AES AES）, WPA2 Personal（AES AES） and TKIP+AES WAP2 （TKIP+AES TKIP+AES）.. Note: 1. T o connect internet through wireless network, the camera SSID number must be the same with the wireless router and other AP device SSID number, 2. Our default camera SSID number is dink. 3.4.7.
All the above information are set up when the device is ready. Users generally do not need to change. In case of any accidental loss, user needs to re-obtain the domain name, and fill it himself, juts do as the above, the user’s name is just the first four characters, and this is for remote access. For example, http: //abcd.ipcam.hk, the user’s name is abcd. The password is DDNS. (The password can be obtained on the device body or contact the supplier).
from the mail service provider. The email notifications are pictures captured by camera when alarm is on. if no email notification is needed, there is no need to choose this one.. 3.4.11. FTP Service Settings Above setting is equally similar to Mail Server Settings，when alarming is on it will send pictures，please enter FTP server, FTP port, FTP user, FTP password, FTP upload directory and FTP mode. The FTP mode has two options: PORT and POSV.
3.4.13. Reset/Firm Ware Upgrade This sector is for camera firmware upgrade, it includes device system firmware and device application firmware. Be careful to apply for it! 3.4.14 Restore factory Settings If users forget password, we can restore ex-factory settings, when click the key, a picture will pop up, Click ok, and wait for 1 minute then you can use it normally. User setting feature restores 3.4.
Central Management System 4. 4.Central please refer to Central Management System User manual 5. Mobile Access 5.1. Smart phon phonee Access The smart phones are the mobile phones with operating system, such as Windows Mobile and Symbian. Due to its powerful function, the web page browser of such phones usually supports Javascript. That’s why it can visit the dynamic pages of the IP camera through web page browser. First of all, the mobile phone must open internet access function.
2. Input the Username and Passoword of the device, and the following interface will appear. There are three log-in options. Click on the third “Sign in” and use Mobile Phone mode. Language is used to select the display language. Do not show next time: When this option is selected, this interface will not appear when you log in next time. It will directly skip to the monitor image..
Description for the monitor image: - 24 MFN-E-A3
Instruction for the Key Function: Update: it is used to refresh the page. If the monitor piture is kept still, you may press this key to update the page. Up, down, left, and right: They are used to rotate the camera P/T. The camera without P/T does not have these keys. Stop: Stop to rotate the camera P/T The Download address of the mobile browser Opera mini: http://mini.opera.com. Download the Opera mini browser according to the mobile model. 6. Others 6.1.
3. Click “virtual server” in the unfolded menu. 4. fill “80” under the right port start or port end end, Server IP address fill "192.168.1.50", protocol select "TCP/UDP"OR”“TCP”, finally don’t forget to click “"save/apply” Detailed information please refers to following photo: When completed port forwarding, you can visit camera through device code in outer net remotely; Common router default visit address are as follow: 1. DLINK ex-factory definition router address is 192.168.0.1 2.
This series produce own variety configured specification. Users can choose the best one according to their requirement.. Image Specification Bullet camera, wired/ wireless selected, indoor Infrared bullet camera wired/wireless selected, infrared 20m/40/50m selected indoor/waterproof selected lightning protection design Wired/Wireless selected, infrared 10 m Audio selected Level & vertical rotation P/T Cell indoor select infrared night vision 20 m Cell indoor overall rotation P/T 5” or 3.
Question: Does centralized monitor interface support Vista & Linux system? Answer: Just Vista system. Right now it do not support Linux system. Question: How to set IP camera the same network segment as PC in LAN Answer: First you can use search bar to find out the camera, then click auto set button. Question: What mode of cell phone does the F series camera allow to visit? Answer: Generally, cell phone with Java MIDP 2.0 program can watch dynamic video.
c) The damages due to floods, fire, lightning strike and other natural calamities or force majored incidents factors d) Repaired item by non-authorized repair centers. All above terms, if these is any changes; they should according to relevant regulations.
8.2.
