Drystar 5302 User manual
DRYSTAR 5302 USER MANUAL This product is registered in China under the registration number: 3 S5 D el d b a A l efine D SF Be d To 02 For more information on Agfa products and Agfa HealthCare products, please visit www.agfa.com, your Point of Knowledge. © Agfa-Gevaert N.V. 2004. No parts of this document may be reproduced, copied, adapted or transmitted in any form or by any means without the written permission of Agfa-Gevaert N.V. Agfa-Gevaert N.V.
DRYSTAR 5302 USER MANUAL Table of contents Chapter 1: Introducing the Drystar 5302 ..................................................5 Drystar 5302 features .....................................................................................6 Safety precautions ..........................................................................................9 Security precautions .....................................................................................12 Safety compliance .............................
DRYSTAR 5302 USER MANUAL 4 2831A EN 20041201
Chapter Introducing the Drystar 5302 This chapter introduces the Drystar 5302 to the user and draws attention to important safety precautions.
DRYSTAR 5302 USER MANUAL Drystar 5302 features The Drystar 5302 is a dry digital tabletop printer for producing medical diagnostic images. It can print multiple formats (8x10” up to 14x17”) of bluebased and clear-based film and offers crisp, dense grayscale images. The Drystar 5302 is a Dicom-only network printer.
DRYSTAR 5302 USER MANUAL " Number of output trays. The Drystar 5302 is equipped with 1 output tray, which is suitable for the multiple formats without any adjustment. " Integrated A#sharp technology A#sharp is a technology that enhances image sharpness for the Drystar 5302. An A#sharp label on the lower tray shows that the imager has been upgraded with this technology.
DRYSTAR 5302 USER MANUAL Customizable features " Consumables. The Drystar 5302 can handle Drystar DT 2B and Drystar DT 2C consumables, both in multiple formats (8x10” up to 14x17”). Software license information " The Drystar 5302 uses software developed by the Apache Software Foundation (http://www.apache.org/licenses/LICENSE).
DRYSTAR 5302 USER MANUAL Safety precautions The Drystar 5302 must only be operated according to its specifications and its intended use. Any operation not corresponding to the specifications or intended use may result in hazards, which in turn may lead to serious injuries or fatal accidents (for example electric shocks). AGFA will not assume any liability whatsoever in these cases. All images created using any image technology can show artifacts which could be mixed up with diagnostic relevant information.
DRYSTAR 5302 USER MANUAL Caution hot: Keep hands clear from the thermal print head. In order to reduce the risk of electric shock, do not remove any covers. Type B equipment: Indicates that the Drystar 5302 complies with the limits for type B equipment. Supplementary protective earth connector: Provides a connection between the Drystar 5302 and the potential equalization busbar of the electrical system as found in medical environments.
DRYSTAR 5302 USER MANUAL continuously from one location to the other. Do not lift the printer by the output tray. Waste disposal and environmental regulations In most countries Drystar film is considered industrial waste and consequently it is not allowed to be disposed as household waste. Please consult your local waste disposal regulations. Agfa recommends having waste Drystar film collected by a licensed company.
DRYSTAR 5302 USER MANUAL Security precautions U.S. Law restricts this device to sale to or on the order of a licensed physician. Printed images should be treated as patient records and should only be viewed by authorized personnel. If the power to the printer is unexpectedly interrupted, ensure that unprinted images are not deleted from the modality prior to printing. To avoid loss of images in such conditions, a UPS (Uninterruptable Power Supply) needs to be supplied to the printer.
DRYSTAR 5302 USER MANUAL Safety compliance EMC issues • USA: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
DRYSTAR 5302 USER MANUAL Radio-interference regulations (interference suppression) FCC Rules 47 CFR part 15 subpart B IEC 60601-1-2 CISPR 11, class A CISPR 22, class A IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-3-2 IEC 61000-3-3 IEC 61000-4-11 ETSI 300330 GB9254-1998(Class A) (for CCC-Mark) GB17625.1-2003 (for CCC-Mark) • • • • • • • • • • • • • • Labels The Drystar 5302 carries the CE, TÜV, cULus and CCC labels.
DRYSTAR 5302 USER MANUAL Privacy and security Within the healthcare industry, several standardization efforts are ongoing as a response to Privacy and Security legislation and regulations. The purpose of this standardization for hospitals and vendors is to enable information sharing, interoperability and to support the workflow of hospitals in a multiple vendor environment.
DRYSTAR 5302 USER MANUAL This CA distributes the certificate to the hospital security responsible or service technician, who for his part: • Imports the device certificate, created by the CA. • Imports the certificates of all peer devices with which communication is authorized, i.e. creates the list of ‘communication allowed’ device certificates.
DRYSTAR 5302 USER MANUAL Operating modes The Drystar 5302 can be operated in five modes: Operator mode, Keyoperator mode, Service mode, Specialist mode and Administrator mode. Operator mode The Operator mode groups all basic functions that are intended for radiographers without special technical skills: • Producing diagnostic usable hardcopies; • Loading consumables; • Ensuring normal operation of the printer. All functions of the Operator mode are described in both User and Reference manuals.
DRYSTAR 5302 USER MANUAL Administrator mode (also known as Security) The Administrator mode functions are reserved for the System Administrator. The Administrator mode is password protected and is only accessible by browser via a remote PC.
DRYSTAR 5302 USER MANUAL Control modes (local and remote) You can control the working of the Drystar 5302 via the local keypad or via a network remote PC. The table below gives an overview of the operating modes you can access locally and/or via the remote PC.
DRYSTAR 5302 USER MANUAL The user interface The Drystar 5302 interfaces with the user via the following controls: Power/Reset button; a keypad and a display; a status indicator LED; audio signals. • • • • Overview of user interface controls 1 2 6 3 4 5 1 Power/Reset button 2 Display 3 Keypad 4 Status indicator LED 5 Film input trays 6 Film output tray Never try to open the printer when the Drystar 5302 is printing a film.
DRYSTAR 5302 USER MANUAL The status indicator LED On the right side of the display, an LED indicates the status of the Drystar 5302. Color / Light Green Red Status Action Constant Ready (stand-by) Proceed Blinking Busy or in keyoperator mode Wait Blinking Warning status Constant Error status Check the display for messages. Refer to ‘Checking the status indicator LED’ on page 157 of the Drystar 5302 Reference manual.
DRYSTAR 5302 USER MANUAL Rear panel 1 2 3 4 At the rear side of the printer, one slot and three connectors are available: 22 1 CF-card slot • To insert an external CF-card for software installation, backup, etc. 2 Network connector • To connect to the hospital network. 3 Input/output connector • To connect a terminal PC (used by the Service engineer). 4 Power connector • To connect the printer power cord.
DRYSTAR 5302 USER MANUAL Working with Compact flash cards (CF-card) The Drystar 5302 is equipped with an external CF-card slot. A CF-card has the following physical characteristics: 1 2 • a flat surface on one side (there is also often a label present), • a small rim on the other side, • connector holes on the opposite side of the rim side.
DRYSTAR 5302 USER MANUAL Removing a CF-card To remove a CF-card from the Drystar 5302 slot: 2 1 1 Push the unlocking lever underneath the CF-card slot. The CF-card is pushed slightly outward. 2 24 Remove the CF-card gently from the slot.
DRYSTAR 5302 USER MANUAL Audio signals The Drystar 5302 gives status information via beeps. The length of the beep indicates the response of the system to a key command. • A short beep means that Drystar 5302 has accepted the key command and is starting the operation. • A long beep means that you have pressed a non-active key or that the Drystar 5302 has rejected the key command. Certain conditions can cause an interval beep. An interval beep accompanies an error or warning message.
DRYSTAR 5302 USER MANUAL The Drystar 5302 keypad features the following keys: Keyoperator key To access the advanced functions of the keyoperator mode. Refer to Chapter 3, ‘Advanced operation (Key-operator mode)’. Escape key To quit the current function or exit a menu without saving modifications. (In key-operator mode) Confirm key • To select a menu. • To accept an entry in a menu. • To move the cursor to the previous entry field. Up key • To scroll upwards.
DRYSTAR 5302 USER MANUAL The display The Drystar 5302 control panel has a backlit LCD display. We distinguish two panel types depending on the selected language: • a backlit LCD display with 4 lines for Western languages (e.g. Dutch, French, Portuguese, Swedish, ...). please WAIT Self Test proceeding • a backlit LCD display with 2 lines for Eastern language (e.g. Greek, Chinese, Korean, Polish, ...). Autotest: CZEKAJ... Whether a display is translated or not depends on the operating mode.
DRYSTAR 5302 USER MANUAL Operator mode In operator mode, appropriate information is displayed in accordance with the status of the printer. The operator basic screen looks as follows, indicating that the Drystar 5302 is ready for operation and that no job is currently being executed.
DRYSTAR 5302 USER MANUAL The active keys are indicated by their respective LEDs. Data entry When entering numerical or alphanumerical data, always adhere to the following principles: • Only (alpha)numerical data can be entered. • During data entry, the field is displayed in reverse mode. • Increment the number in a(n) (alpha)numerical entry field by pressing the • • • • • • • Up key.
DRYSTAR 5302 USER MANUAL Switching on the Drystar 5302 Before switching on the Drystar 5302, read the safety instructions. Refer to ‘Safety precautions’ on page 9. Follow the procedure below to ensure proper startup of the Drystar 5302 and to check that everything is working correctly. 1 Check that the power cord is plugged in and then switch on the printer by pressing the Power/Reset button. On the display, the following message is displayed.
DRYSTAR 5302 USER MANUAL 2 The printer is ready for operation: • If, on the front panel display, the READY message is shown, the status indicator LED is constantly green. READY It takes 13 minutes (starting up of the Drystar 5302 and heating up of the thermal print head) before you can start printing. The display will inform you that the printer is warming up: WARMING UP Please wait • If, on the front panel display, the print queue screen is shown, the status indicator LED is green and blinking.
DRYSTAR 5302 USER MANUAL Switching off the Drystar 5302 When you want to switch off the printer, it is recommended to follow the procedure as described below, to make sure that any pending print jobs have finished printing. 1 Make sure that pending jobs are correctly finished. If necessary, follow the procedure to stop printing. 2 Press the Power/Reset button to switch off the Drystar 5302.
Chapter Basic operation (Operator mode) This chapter will inform on how to manage the print queue, how to print films with priority and how to load new films.
DRYSTAR 5302 USER MANUAL Overview of operator functions This section focuses on the basic operating principles of the Drystar 5302. After reading this chapter, the operator should be able to produce diagnostic usable hardcopies. No special technical skills are required. All basic operator functions can be activated directly by pressing a single key on the keypad. Function / Task 34 Description Page ‘Managing the print queue’ Jobs that have been received are put in a print queue, waiting to be printed.
DRYSTAR 5302 USER MANUAL Managing the print queue You can always check the status of the print jobs. Keep in mind that one print job can hold several films to be printed. In accordance with the acquisition modality used and with the actual settings, films can be grouped in a folder to be submitted as one print job for the Drystar 5302. Refer to the User manual of the acquisition modality for more information.
DRYSTAR 5302 USER MANUAL A description of the possible status of the jobs is listed in the table below: Status Description PR Printing Printing of this job is in progress. CA Calculating The necessary calculations are already being made before printing of the job can be started. WA Waiting Jobs are queued in the printer memory. On the print queue screen the modality name defined during installation will be used to refer to the corresponding modality.
DRYSTAR 5302 USER MANUAL About Drystar 5302 consumables The Drystar 5302 can handle blue-transparent and clear-transparent films. Available film formats are 8x10”, 10x12”, 11x14”, 14x14” and 14x17”. When a new film pack is loaded, the Film Identification tag is read and the printer settings are automatically adjusted. The key-operator can overrule the film settings for the input tray. Refer to ‘Changing the configuration settings’ on page 56 of the Drystar 5302 Reference manual.
DRYSTAR 5302 USER MANUAL Loading films This section describes how to load the Drystar 5302 with appropriate films. The Drystar 5302 can be loaded with 8x10”, 10x12”, 11x14”, 14x14” and 14x17” films. The Drystar 5302 can be loaded with new films in full daylight. Loading films is easy and can be done very quickly. Follow the procedures as described in this section.
DRYSTAR 5302 USER MANUAL When the Drystar 5302 is in the ready state and an input tray is empty: 3 The display shows the following message: Lower input tray empty OK to Open the INPUT TRAY 4 Open the empty input tray. To avoid possible film jams, make sure to open input tray all the way.
DRYSTAR 5302 USER MANUAL 6 Remove the white (protective) film sheet. 7 Take film pack, and open it. Verify that the film type on the film pack corresponds with the sticker on the tray! If you do use an other film type, you are advised to change the label on the tray. You can put the film pack onto a table to make manipulation easier. Before you do this, make sure that the table is dust-free! 8 40 Remove the sticker from the film pack.
DRYSTAR 5302 USER MANUAL 9 Remove the plastic film bag partially. 10 Slide the film pack into the input tray, and remove the plastic film bag completely.
DRYSTAR 5302 USER MANUAL 11 Tear the plastic tape from around the film pack. 12 Close the input tray. The Drystar 5302 resumes printing as soon as the tray is closed. Loading instructions are also available on the input tray cover. Never reuse a jammed film. Refer to ‘Clearing of film jams’ on page 161 of the Drystar 5302 Reference manual.
DRYSTAR 5302 USER MANUAL Checking the correct position of a film in the input tray You can verify that the film is properly loaded by watching the lower right corner of the films in the input tray. The rounding of this corner should be smaller than the other three corners. This is also indicated on the sticker at the right side of the input tray cover. When a new film is loaded, the Film Identification tag is read and the printer settings are automatically adjusted.
DRYSTAR 5302 USER MANUAL 44 Basic operation (Operator mode) 2831A EN 20041201
