Global Services North America Wilmington MA 01887 :ANAPURNA M4F AGFA UV INKJET PRINTER SITE PREPARATION GUIDE Distribution: Customer Sales Service Dealer 03/17/10 Revision 5.
Global Services North America Wilmington MA 01887 Table of Contents Purpose: ---------------------------------------------------------------------------------------------------------------------------- 3 Scope: ------------------------------------------------------------------------------------------------------------------------------- 3 Major Project Milestones:----------------------------------------------------------------------------------------------------- 3 Dock door and hallway access-------------
Global Services North America Wilmington MA 01887 Purpose The purpose of this document is to assist the local service representative, who is responsible for configuring and installing the :Anapurna. This document will help to ensure the site will be ready and the customer is informed of their responsibilities. Please go through all the information provided in this document thoroughly with the customer. Have the customer sign the :Anapurna System Site Check List.
Dock & building access Global Services North America Wilmington MA 01887 System Dimensions and Weights Dimensions Uncrated H = 63 Inches (1600 mm) Dimensions Crated H = 71 Inches (1800 mm) Weight: Crated: 3087 lbs (1400 Kg) W = 141 Inches (3570 mm) D = 57 Inches (1450 mm) W = 153 Inches D = 61 Inches Uncrated:2165 lbs (980 Kg) Accessory Box Width 76” (192 cm) (3800 mm) (1550 mm) Height 47 “ (119 cm) Depth 52 “ (133 cm) Weight 595 lbs (270 Kg) Shipping and Delivery No Truck Height Loading Dock:
Global Services North America Wilmington MA 01887 Dock & building access Foot Print and Working Area: Power and Air Connection Points: The power/air connection points are indicated in the diagram above with the letters A, B, and C A – The power cable entry point lower chassis – near the rear left leveling foot. B – Electrical terminal block location inside the printer, where the power cable connects.
Global Services North America Wilmington MA 01887 Compressed Air Supply Engine Air Connection: An adapter (shown below) is needed to connect the air hose from the air regulator to the printer. This should be purchased locally. Compressor: Engine Air Volume: 3 - 5 HP, min 60 - 80 gallons or better tank. The compressor regulator should be set between 105 - 110 PSI for trip OFF and to 85 PSI to trip ON. Air from the compressor, going to the Anapurna must be regulated to 80 PSI.
Global Services North America Wilmington MA 01887 RIP Software and PC Platform Wasatch RIP The Wasatch SoftRip is provided for raster image processing of images. Install the Wasatch SoftRIP on a PC, which meets the following platform specifications. Minimum Recommended System requirements for Anapurna M4F ¾ ¾ ¾ ¾ CPU Type: Core 2 Duo, 3.
Global Services North America Wilmington MA 01887 AC Power Requirements Power Requirements for the Anapurna M4F: The following electrical requirements must be provided to your electrician. • Single phase, 208 Y (Wye) power • 40 Amp, 60Hz, dedicated circuit with ground, no neutral • The electrician must provide the proper power cord and plug/receptacles (See Note 3) • Buck boost transformer wiring diagram is on page 10 Important 1.
Global Services North America Wilmington MA 01887 AC Power Requirements The Buck/Boost Transformer The Anapurna M4F UV Printers requires power in the 230 – 240 VAC range for the UV lamps to properly cure the ink. At 208 Volts the customer will have curing problems and the lamps will fail prematurely. Buck/Boost Transformer and Specifications: • • • • • KVA Rating: 1.5 Primary Volts: 120/240 Secondary Volts: 16/32 Sola Hevi Duty Catalog #: HS20F1.5A Sola Hevi Duty Website is: www.solaheviduty.
Global Services North America Wilmington MA 01887 AC Power Requirements Wiring Diagram to Boost Voltage (+32) for Single Phase Power: Input Voltage = 208 V Output Voltage = 236 V This diagram illustrates how to connect a 1.5 KVA, 16/32 Volt buck boost transformer. This wiring configuration boosts the line voltage from 208 to 236 Volts. Diagrams such as this one is provided by the Buck Boost transformer manufacturer. It is normally found on the data sheet that ships with each transformer.
Global Services North America Wilmington MA 01887 AC Power Requirements Sample Buck/Boost Transformer: This photo is showing a sample Buck Boost Transformer from Sola Hevi-Duty, it is a 1.5 KVA version, catalog # HS20F1.5A and it weights approximately 38 pounds or 17.2 Kgs.
Global Services North America Wilmington MA 01887 Site Readiness Check List Information to Check Forklift Yes No Lateral fork movement capability. Proper lifting rating? (Pg.4) Length of forks should be 60 inches (152.
Global Services North America Wilmington MA 01887 Customer Responsibilities The following information has been explained to the customer during the site preparation visit.
Global Services North America Wilmington MA 01887 General Information Environmental Requirements Room Operating Temperature: Range 68° F to 83° F (20 - 28° C) Ideal 72° F (22° C) (Room air temperature should not to exceed 126º F or 52 ºC) Humidity: Room Air Exchange: Range 35% to 75% RH (non-condensing) Ideal 40% 10 times per hour. The room must be clean and dust free so that no contamination can adversely affect the print heads and print quality.
