Service manual

Avantra 36/44 Service Manual
I-8 Index
Power Supply Fuse 2-14
Powered Media Take-up Cassette 2-27
Power-up Boot Diagnostics 3-2
confidence checks 3-2
debug monitor mode 3-2
initializing 3-2
main functions 3-2
modem/auto-dial-out feature 3-2
overview 3-2
Power-up Boot Sequence 3-3
Pre-installation Checks 1-4
Preparing Media Transport Retainer Bracket 1-
18
Preventive Maintenance 6-1
Procedure, System Leveling 5-10
Procedure, Voltage Check 5-11
Procedures, Local Modem Connection 3-65
Prog DEC/DUPLO (defined) 3-48
Prog OCP (defined) 3-48
Program Bridge FLASHROM 3-56
Program Debugging Mode 3-47
Program K1 FLASHROM 3-55
Program OCP FLASHROM 3-54
Pulse Width Modulation (PWM) Adjustment
Procedure 5-11
Pump
location 1-12
Punch Remnants 6-3
Punch Shoe
location 4-19
Punches
distances to parameter 5-3
PWM 5-11
R
Raising the Imagesetter 1-12
RAM Test 3-10
Raster Image Processor 3-2
Real-Time clock 3-47
Recommended Remote Modem 3-63
Register Test, DAC 3-6
Register Test, DEC Offgate 3-8
Register Test, DEC Vacuum 3-8
Register Test, OCP 3-7
Register Test, Offgate 3-6
Register Test, Ongate 3-6
Register Test, Vacuum 3-6
Remote Connection Procedures, Modem 3-66
Remote Connection, Exiting 3-67
Remote Diagnostic Center Telephone
Numbers 3-64
Remote Diagnostic Port 3-17, 3-19
Remote Diagnostics
equipment requirements 3-61
modem configuration 3-61
Remote Modem 3-63
Remote Modem Configuration 3-63
Remote Modem Connection Procedures 3-64
Remote Modem, Connecting 3-64
Remote Modem, Recommended 3-63
Remote Session 3-66
Remote Site Equipment
Avantra Diagnostic diskette 3-61
Dolch PC 3-61
modem 3-61
Remote Terminal Error Reportiing 3-5
Removing Light Shields 1-20
Removing Lower Media Transport Retainer
Bracket 1-17
Removing Packing Materials 1-10
Removing Packing Materials from Imagesetter
Front 1-14
Removing Packing Materials from Rear of
Imagesetter 1-15
Removing Take-up Light Shield 1-18
Removing the Channel Bolts 1-9
Removing the Diaper 1-8
Removing the End Platesplate 1-8
Removing Tie Down Bracket 1-16
Reporting, Errors 3-5
Requirements, Local Modem 3-65
Reset Comm Port 3-44
Reset Command 3-44, 3-67
Reset Commands 3-44
Retainer Bracket, Lower 1-16
Retainer Bracket, Uppear 1-17
Rev Bump Time
definition 3-34
Revisions, Firmware 3-38
Rev-TU Servo Curr
definition 3-34
Rev-TU Servo Speed
definition 3-34
Rewind Motors 2-26
Right Side Cover
remove and replace 4-3
Right/Left Side Covers
remove/replace 4-3
RIP 2-4, 2-8, 3-2
Rollers, Drive 2-27
ROM 3-10
RS-232 Serial Port 3-17
RS-423 Driver 2-12
S
Save and Restore System Parameters 3-49
Save DEC (DSP) (defined) 3-48
Save DEC(CORR) (defined) 3-48
Save/Restore DEC DSP and DEC Correction
Tables 3-51
Save/Restore Operator’s Control Panel (OCP)
User Parameters 3-52
SDM 2-11, 2-12
SDM Board 4-13, 4-20
SDM to DEC Interface 2-12
SDMs 4-32
Selectable Tests 3-20
Sensor
Cutter Home 4-22
jam 4-18