Service manual

Section I: Imagesetter
Index I-11
remove/replace 4-32
Telephone Numbers, Remote Diagnostic
Center 3-64
Telephone Requirements 1-3
Temperature
operating 1-2
shipping 1-2
Test
BOOT 3-24
carriage 3-8, 3-22
DEC 3-21
DEC micro-controller descriptions 3-8
DEC offgate register 3-8
DEC ongate register 3-8
DEC to DSP SPI link 3-8
DEC vacuum register 3-8
display controller 3-11
display RAM 3-11
media 3-23
menu 3-20
OCP 3-23
OCP register 3-7
offgate register 3-6
ongate register 3-6
selectable 3-20
supply motors 3-9
vacuum register 3-6
Test Bridge 3-43
Test Descripions, DIAG Micro-controller 3-6
Test Descriptions, DEC Micro-controller 3-8
Test Descriptions, OCP Micro-controller 3-11
Test Descriptions,DSP Micro-controller 3-10
Test Menu 3-20
Test Procedure, Slack Loop 5-21
Test, Carriage 3-8
Test, Correction SRAM 3-7
Test, Display Controller 3-11
Test, Display RAM 3-11
Test, Port 3-10
Test, RAM 3-10
Test, Spinner Verify 3-10
Test, SRAM Checksum 3-7
Test, Supply Motors 3-9
Test, Take-up Motors 3-9
Test, take-up motors 3-9
Test, Video Data Path 3-9
Test,Video Data Path 3-9
Tests, Boot 3-24
Tests, Bridge 3-24
Tests, Carriage 3-22
Tests, Media 3-22, 3-23
Tests, OCP 3-23
Tie Down Bracket 1-16
Toggle Comm. Display 3-47
Tool Kit 1-5
Tools
diagnostics 3-1
Top Cover
location 4-58
Top Cover, Imagesetter 4-3
Top Panel
location 4-6
lock slots
location 4-6
Training, Customer Application 1-24
Transfer Tool
carriage installation 4-45
carriage removal 4-42
Transfer Tool Installation 4-40
Transport Retainer Bracket 1-17
Troubleshooting Sensor Problems 3-39
U
Unlocking the Carriage 1-20, 1-21
Unlocking the Imagesetter 1-13
Unlocking the Vacuum Pump 1-19
Unpacking the Imagesetter 1-5
UpBrdg Fast Spd
definition 3-31
UpBrdg Slow Spd
definition 3-31
Upper Media Transport Retainer Bracket 1-17
upply 3-33
Upply Cassette Spindle A/b Position Sensors
location 4-65
upply Hold Current
range 3-33
User Interface 3-20
sub-menus 3-20
User Interface Sub-menus
DAC RAMPS 3-22
DEC 3-21
MEDIA TESTS 3-23
TEST 3-20
User Parameters 3-36, 3-52
bridge primitives 3-43
carriage motion 3-41
cassette 3-37
display error log 3-38
display sensors 3-39
engine primitives 3-41
operational statistics 3-37
User Parameters, OCP 3-36
Using the Jack Screw 1-11
Utilities Menu Items
edit file 3-47
execute PC imager 3-46
feed/error disable 3-47
hard reset 3-44
modem functions 3-45
monitor mode 3-46
new engine/restart 3-44
reset communication port 3-44
set config passwd 3-47
toggle comm. display 3-47
Utilities, Modem 3-44
V
Vacuum Pump, Unlocking 1-19