User`s guide

Index-4
Index
Channel Position softkey, 1-17
customizing
, 1-17
viewing
, 1-14
Freelance, using
, 4-23
frequency
segments, editing
, 6-34
signals, deleting
, 6-35
span, decreasing
, 5-11
span, setting
, 1-36
frequency bands
adding
, 1-86
changing
, 1-85
deleting
, 1-87
setting
, 1-84
frequency drift
, 5-5
frequency list sweep of 26 points
,
2-28
frequency offset mode operation
,
2-10
frequency offset mode, conversion
compression
, 2-39
frequency offset mode, conversion
loss
, 2-13
frequency offset operation
, 7-84
frequency range, setting
, 1-5
frequency range, setting for time
domain low pass
, 3-15
frequency response
, 7-40
frequency response and isolation
error corrections
, 6-17
reflection measurements
, 6-19
transmission measurements
,
6-17
frequency response error
corrections
, 6-12
receiver calibration
, 6-15
response error correction for
reflection measurements
,
6-12
response error correction for
transmission
measurements
, 6-14
frequency response of calibration
standards
, 6-5
electrical offset
, 6-6
fringe capacitance
, 6-6
fringe capacitance
, 6-6
full two-port calibration
, 7-55
full two-port error correction
, 6-29
G
gain
, 1-58
gain compression
measuring
, 1-54
using linear sweep
, 1-56
gating
, 3-35, 7-7
selecting gate shape
, 3-36
setting the gate
, 3-35
general
, 8-6
generating files in a loop counter
example
, 1-115
German FTZ emissions
requirements
, 8-7
gosub sequence command
, 1-107
GPIB operation
address menu
, 7-79
GPIB STATUS indicators
, 7-78
local key
, 7-77
pass control mode
, 7-78
system controller mode
, 7-78
talker/listener mode
, 7-78
using the parallel port
, 7-79
GPIO mode
, 1-107, 7-80
graphic files
saving measurement results as
,
4-45
grids
moving marker information off
the grids
, 1-26
group delay
, 1-47
group delay format
, 7-25
group delay measurements
, 2-34
group delay principles
, 7-30
H
high dynamic range
measurement
, 2-23
swept RF/IF conversion loss
,
2-20
high dynamic range
measurement
, 2-23
high dynamic range swept RF/IF
conversion loss
measurement parameters for IF
range
, 2-20
power meter calibration over IF
range
, 2-20
powermetercalibration overRF
range
, 2-23
receiver calibration over IF
range
, 2-22
RF frequency range
, 2-22
high power
measurements
, 1-60, 1-66
high power measurements
additional setup
, 1-61
initial setup
, 1-60
power levels, determining
, 1-60
high power measurments
attenuator settings, selecting
,
1-62
final setup
, 1-64
power ranges, selecting
, 1-62
horizontal axis
, 3-13, 3-14, 3-16,
3-20, 3-23
how RF and IF are defined
, 2-7
how to
make high power
measurements
, 1-60
HPGL
compatible printer
, 4-21
initialization sequence, sending
to the printer
, 4-26
initialization sequence, storing
,
4-25
HPGL compatible printer
, 4-25
HPGL/2 compatible printer
, 4-10
I
IF bandwidth reduction
, 7-36
IF bandwidth, setting segment
,
7-19
IF delay, detecting
, 5-11
IF detection
, 7-6
IF range
measurement parameters
, 2-20
power meter calibration
, 2-20
receiver calibration
, 2-22
IF, defining
, 2-7
imaginary format
, 7-30
improving measurement results
,
5-8
decreasing the sweep rate
, 5-9
decreasing time delay
, 5-9
improving raw source match and
load match for TRL*/LRM*
calibration
, 7-70
increase sweep speed
using fast 2-port calibration
,
5-13
increasing dynamic range
, 5-15
increasing test port input
power
, 5-15
reducingreceiver crosstalk
, 5-15
reducingthereceivernoisefloor
,
5-15
increasing measurement
accuracy
, 5-4
connector repeatability
, 5-4
frequency drift
, 5-5
interconnecting cables
, 5-4
performance verification
, 5-5
reference plane and port
extensions
, 5-5
temperature drift
, 5-5
increasing sweep speed
, 5-10
activating chop sweep mode
,
5-13
decreasing the frequency span
,
5-11