User`s guide

Index-10
Index
generatingfiles in aloopcounter
example
, 1-115
in-depth information
, 1-105
jumps to itself
, 1-112
limit test example
, 1-117
loading from a disk
, 1-104
loop counter example
, 1-114
naming files
, 1-103
printing
, 1-105
purging from a disk
, 1-104
running
, 1-100
size
, 1-106
stopping
, 1-100
storing to disk
, 1-104
sequencing
special functions menu
, 1-111
test
, 1-98
servicing
, 8-6
setting
auto sweep time mode
, 5-12
frequencyrangefortimedomain
low pass
, 3-15
gate
, 3-35
setting ripple limits
, 1-82–1-85
setting segment IF bandwidth
,
7-19
setting segment power
, 7-18
setting the sweep type
, 5-12
setting up bandwidth test limits
,
1-92–1-94
shipment for service
, 8-2
sidelobes
, 3-27
single page plots, outputting
using a printer
, 4-26
single point limits
, 1-78
sloping limit line
, 1-76
small signal transient response,
measuring
, 3-19
smith chart format
, 7-26
smith chart markers
, 1-33
smoothing
, 7-8, 7-34
softkey
4 Param Displays
, 1-18
channel position
, 1-17
solving problems with printing or
plotting
, 4-35
solving problems with saving or
recalling files
, 4-54
using an external disk drive
,
4-54
source attenuator switch
protection
, 7-13
repetitive switching of the
attenuator
, 7-13
source match
, 7-39
source match and load match
,
7-69
source mismatches, minimizing
,
2-4
source power, setting
, 1-5
source step attenuator
, 7-4
S-parameter menu
analog in menu
, 7-22
conversion menu
, 7-22
S-parameters
, 7-20
S-parameter menu
, 7-22
understanding
, 7-20
S-parmeters menu
input ports menu
, 7-23
specific amplitude
, 1-39
bandwidth, searching for
, 1-41
maximum amplitude, searching
for
, 1-39
minimum amplitude, searching
for
, 1-39
target amplitude, searching for
,
1-40
tracking the amplitude
, 1-41
spreadsheet, saving test filefor a
,
4-44
spurious responses, reducing the
effect of
, 2-5
standards, calibration
, 6-5
start frequency, setting
, 1-34
starting the ripple test
, 1-87
statistics of measurement data,
calculating
, 1-42
stepped edit list menu
, 7-16
stepped edit subsweep menu
, 7-16
stepped list frequency sweep
, 7-15
segment menu
, 7-16
stepped edit list menu
, 7-16
stepped edit subsweep menu
,
7-16
stepped list mode
, 1-68
stimulus state, eror-correction
,
6-9
stop frequencies, minimum
allowable
, 3-16
stop frequency, setting
, 1-35
stoping the ripple test
, 1-87
stopping a sequence
, 1-100
storing
exit HPGL mode and form feed
sequence
, 4-26
HPGL initialization sequence
,
4-25
sequence on a disk
, 1-104
sweep
rate, decreasing
, 5-9
retrace
, 5-7
speed, increasing
, 5-10
type, setting
, 5-12
sweep time
, 7-11
auto sweep time mode
, 7-11
manual sweep time mode
, 7-11
minimum sweep time
, 7-11
sweep types
, 7-15
CW time sweep
, 7-19
linear frequency sweep
, 7-15
logarithmic frequency sweep
,
7-15
power sweep
, 7-19
selecting sweep modes
, 7-19
stepped list frequency sweep
,
7-15
swept list frequency sweep
, 7-17
sweep-to-sweep averaging
, 7-6
swept edit list menu
, 7-17
swept edit subsweep menu
, 7-17
swept list frequency sweep
, 7-17
setting segment IF bandwidth
,
7-19
setting segment power
, 7-18
swept edit list menu
, 7-17
swept edit subsweep menu
, 7-17
swept list mode
calibrate
, 1-71
characteristics of the filter
, 1-69
device under test, connect
, 1-68
measure
, 1-71
measurement parameters
, 1-69
stepped list mode
, 1-68
to test a device
, 1-68
swept list mode, using
, 5-10
swept RF/IF conversion loss, high
dynamic range
, 2-20
switch protection, source
attenuator
, 7-13
SWR format
, 7-29
SWR/return loss
, 2-49
synthesized source, built-in
, 7-3
system
bandwidth, changing
, 5-16
bandwidth, widening
, 5-12
system controller mode
, 7-78
system operation
, 7-3
built-in synthesized source
, 7-3
built-in test set
, 7-4
microprocessor
, 7-4
receiver block
, 7-4
required peripheral equipment
,
7-4
systematic errors
, 7-41
T
taking care of microwave
connectors
, 5-3
talker/listener mode
, 7-78
target amplitude, searching for
,
1-40