User`s guide

Index
Index-4
verifying 1-29, 1-31
options 1-6, 4-3
and accessories 1-6
display 3-26
power cable 1-13
oscilloscope
cleaning 1-35
inspecting 1-3
resetting 3-7
using 3-2
oscilloscope controls 4-3
oscilloscope feet 1-26
oscilloscope front panel 3-3, 3-4, 3-6
oscilloscope graticule 3-6
oscilloscope operation
verifying 1-29, 1-31
oscilloscope probes, see probes
overdriving vertical amplifiers 3-27, 3-50
P
package contents 1-3, 1-4, 1-5
parallel printers 1-15
parameters
trigger 3-56
performance specifications 4-3
plugs
power 1-13
pointer
moving 3-30
pointing device 1-6
connecting 1-17
verifying operation 1-29, 1-31
position
adjusting digital channel’s vertical
3-14
adjusting horizontal 3-15, 3-28, 3-48
adjusting vertical 3-13
horizontal 3-23, 3-24, 3-49
positioning markers 3-19
power
applying 1-27
connecting 1-12
requirements 1-12
turning off 1-28
power cables 1-13
preferences for dialog boxes 3-58
preset measurements 3-20
printer
cables 1-6, 1-15
printers 1-6
connecting 1-15
probes 1-6
connecting 1-19
information system 4-2
setting characteristics of 3-45
probing a circuit 1-19
problems
information system 4-3
Q
question mark button 4-10
quick measurements 3-6, 3-20
QuickMeas key 3-20
R
radio button 3-30, 3-31
recalling waveforms and setups
information system 4-2
Recovery Disks 3-61
reducing screen clutter 3-58
reference
horizontal 3-46
reference topics 4-7
repair and calibration services 1-6
Repetitive Strain Injury 2-2
Description 2-3
Using the Mouse 2-4
reset
measurements and statistics 3-38
oscilloscope 3-7
right horizontal reference 3-28, 3-46
right-click 3-30, 3-34
RJ-45 connector 1-15
LAN card 1-15
RSI
Description 2-3
Introduction 2-2
Using the Mouse 2-4
run 3-37
button 3-23, 3-24
Run key 3-8
run/stop
controls 3-28
running acquisition 3-5
S
saving waveforms and setups
information system 4-2
scaling
adjusting vertical 3-13, 3-44
vertical 3-5, 3-23, 3-24
screen clutter
simplifying 3-58
screen saver 1-27
seconds per division
adjusting 3-15
in delayed sweep 3-16
setting 3-47
seconds per division setting 3-23, 3-24
selecting
commands 3-33, 3-34
waveform features for measurement
3-25
waveforms for measurement 3-6
serial printers 1-15
service
repair and calibration 1-6
set up trigger 3-5
setting
dialog box preferences 3-58
edge trigger 3-17
horizontal reference 3-46
sweep speed 3-47
trigger position 3-46
setup
channel 3-45
default 1-29, 1-31, 3-5, 3-7
dialog boxes 3-58
horizontal 3-28, 3-49
trigger 3-29, 3-56, 3-57
Setup Guide 4-3
steps 4-9
topics 4-8
sizing
adjusting digital channel’s vertical
3-14
slope
trigger 3-17, 3-57
Slope key 3-17
SMA to BNC Adaptors
connecting 1-20
software magnification of waveforms
3-50