User Manual
Table Of Contents
- 08360125.pdf
- Title Page
- Table of Contents
- 1: Equipment Required
- 2: Performance Tests
- How to Use This Chapter
- List of Tests
- Operation Verification
- 1. Self-Tests
- 2. Power Accuracy
- 3. Power Flatness
- 4. Maximum Leveled Power
- PERFORMANCE TESTS
- 1. Internal Timebase: Aging Rate
- 2. Swept Frequency Accuracy
- 3. Frequency Switching Time
- 4. Power Accuracy
- 5. Power Flatness
- 6. Maximum Leveled Power
- 7. External Leveling
- 8. Spurious Signals (Harmonics & Subharmonics)
- 9. Spurious Signals (Non-Harmonic)
- 10. Spurious Signals (Line-Related)
- 11. Single Sideband Phase Noise
- 12. Pulse Modulation On/Off Ratio (For B-Series Only)
- 13. Pulse Performance (For B-Series Only)
- 14. Pulse Performance (Alternate Procedure) (For B-Series Only)
- 15. Pulse Modulation Video Feedthrough (For B-Series Only)
- 16. AM Accuracy (For B-Series Only)
- 17. AM Bandwidth (For B-Series Only)
- 18. AM Dynamic Range (For B-Series Only)
- 19. FM Accuracy (For B-Series Only)
- 20. FM Bandwidth (For B-Series Only)
- 21. Maximum FM Deviation (For B-Series Only)
- 22. Internal Pulse Accuracy (Option 002) (For B-Series Only)
- 23. Modulation Meter (Option 002) ( For B-Series Only)
- 3: Adjustments
- How To Use This Chapter
- Equipment Required
- Cautions And Warnings
- List of Adjustments
- 1. 10 MHz Standard
- 2. Sweep Ramp
- 3. Sampler Assembly
- 4. YO Driver +10 V Reference
- 5. YO Driver Gain and Linearity
- 6. YO Loop Gain
- 7. Amplifier/Multiplier Adjustments
- 8. Amplifier/Filter Adjustments
- 9. Low Power SRD Bias
- 10. Modulator Offset and Gain
- 11. ALC Power Level Accuracy
- 12. Power Flatness
- 13. AM/FM DAC Offset and Gain (Option 002) (HP 8360 B-Series Only)
- 14. AM Accuracy (HP 8360 B-Series Only)
- 15. AM Offset (HP 8360 L-Series Only)
- 16. AM Delay (HP 8360 B-Series Only)
- 17. FM Gain (HP 8360 B-Series Only)
- 18. Square Wave Symmetry
- 19. AM Input Impedance (HP 8360 B-Series Only)
- 20. FM Input Impedance (HP 8360 B-Series Only)
- 21. Modulation Generator Flatness (Option 002) (HP 8360 B-Series Only)
- 22. External Trigger Edge Selection
- 23. Volts/GHz
- 24. A9 Pulse Board Jumper (W1)
- 25. Selftest Patches (HP 8360 L-Series Only)
- 4: Calibration Constants
- 5: Automated Tests
- Introduction
- Setting Up the System
- Installing Software
- Running the Software
- AUTOMATED PERFORMANCE TESTS
- 1. Step Attenuator Flatness Test
- 2. Power Flatness and Accuracy Test
- AUTOMATED ADJUSTMENTS
- 1. Step Attenuator Flatness Adjustment
- 2. YO Delay Adjustment
- 3. ADC Adjustment
- 4. Power Flatness Adjustment
- Utilities
- 1. Front Panel Emulation
- 2. Calibration Constants
- 3. Self-Test
- 4. Power Sensor Configuration and Calibration Factor File
- 6: Menu Maps
- 7: Disassembly and Replacement Procedures
- Introduction
- Front Panel Disassembly and Reassembly
- 1. Preliminary Steps
- 2. Front Panel Removal
- 3. A3 Front Panel Processor Removal
- 4. A21 Alphanumeric Display Removal
- 5. A2 Source Module Interface Removal
- 6. RPG1 Rotary Pulse Generator Removal
- 7. J1 RF Output Connector Removal
- 8. Front Panel BNC Connectors Removal
- 9. A1 Keyboard Removal
- 10. Display Filter Removal
- 11. A1 Keyboard Reassembly
- 12. Front Panel Reassemblies
- Rear Panel Disassembly and Reassembly
- 1. Preliminary Steps
- 2. B1 Fan Removal
- 3. Rear Panel BNC Connectors Removal and Aux Output Disconnection
- 4. J1 RF Output Connector Removal (Option 004)
- 5. Rear Panel Removal
- 6. A23 10 MHz Reference Standard Removal
- 7. T1 Transformer Removal
- 8. A19 Rear Panel Interface Removal
- 9. Voltage Selector Switch Removal
- 10. Fuse Housing Removal
- 11. FL1 Line Filter Removal
- 12. Option 004 BNC Connectors Removal
- RF Deck Disassembly and Reassembly
- 1. Preliminary Steps
- 2. Lift Up the RF Deck
- 3. A20 RF Interface Removal
- 4. Microcircuit Removal
- Motherboard Disassembly and Reassembly
- 1. Preliminary Steps
- 2. Front Panel Removal
- 3. J1 RF Output Connector Removal (Front Panel)
- 4. J1 RF Output Connector Removal (Option 004)
- 5. Rear Panel Removal
- 6. Major Assemblies Removal
- 7. RF Deck Removal
- 8. Motherboard Removal
- 8: Post-Repair
- 9: Replaceable Parts
- 10: Preventive Maintenance
- 11: Option Retrofits
- Introduction
- Add Attenuator (Add Option 001)
- Delete Attenuator (Delete Option 001)
- Add Modulation/Generator (Add Option 002)
- Rear Panel RF Output (Add Option 004)
- Front Panel RF Output (Delete Option 004)
- 1 Hz Capability (Add Option 008)
- MATE Compatibility (Add Option 700)
- Rack Mount Slide Kit (Add Option 806)
- Rack Flange Kit Without Handles (Add Option 908)
- Extra Manual Set (Add Option 910)
- Rack Flange Kit With Handles (Add Option 913)
- 12: Instrument History
- Index