User`s guide
4-3. Block Diagram of a Spectrum Analyzer/Tracking-Generator Measurement System
4-7
4-4. Transmission Measurement Test Setup
....................
4-8
4-5. Tracking-Generator Output Power Activated
.................
4-9
4-6. Spectrum Analyzer Settings According to the Measurement Requirement
...
4-9
4-7. Decrease the Resolution Bandwidth to Improve Sensitivity
..........
4-10
4-8. Manual Tracking Adjustment Compensates for Tracking Error
........
4-10
4-9. Normalized Trace
.............................
4-11
4-10. Measure the Rejection Range with Delta Markers
..............
4-12
4-l 1. Demodulation of an FM Signal
.......................
4-13
4-12. Continuous Demodulation of an FM Signal
..................
4-14
4-13. Triggering on an Odd Field of a Video Format
................
4-15
4-14. Triggering on an Even Field of a Video Format
...............
4-16
4-15. Reflection Measurement Short Calibration Test Setup
.............
4-17
4-16. Measuring the Return Loss of the Filter
...................
4-18
4-
17. Time-Gate Utility Display
..........................
4-19
4-18. Viewing Time-Sharing of a Frequency with an Oscilloscope
..........
4-23
4-19. Viewing Time-Sharing of a Frequency with a Spectrum Analyzer
.......
4-24
4-20. Pulse Repetition Interval and Pulse Width (with Two Signals Present)
.....
4-25
4-21. Test Setup for Option 105
.........................
4-27
4-22. Setting the Center Frequency, Span, and Reference Level
..........
4-28
4-23. Setting the Sweep Time
..........................
4-28
4-24. Setting the Gate Delay and Gate Length Using an Oscilloscope
........
4-29
4-25. Using Time-Gating to View Signal 1
.....................
4-30
4-26. Placing the Gate Output During the Second Signal
..............
4-31
4-27. Viewing Both Signals with Time-Gating
...................
4-32
4-28. Gate Not Occurring During the Pulse
....................
4-33
4-29. Gate is Occurring at the Beginning of the Pulse
...............
4-33
4-30. Self-Calibration Data Results
........................
4-36
4-31. Rear Panel Connections for Option 105
...................
4-36
4-32. Gate On
..................................
4-37
4-33. Using the Level Gate Control
........................
4-38
4-34. N
dB
Bandwidth Measurement
.......................
4-39
4-35. Percent Amplitude Modulation Measurement
................
4-40
4-36. Third-Order Intermodulation Measurement
.................
4-42
4-37. Occupied Bandwidth
............................
4-44
4-38. Adjacent Channel Power
..........................
4-46
4-39. Adjacent Channel Power Extended
.....................
4-46
4-40. Adjacent Channel Power Graph
.......................
4-47
4-41. Channel Power
..............................
4-48
4-42. Channel Power Graph
...........................
4-49
5-1. Marker
‘Ihble
Display
............................
5-2
5-2. Peak
‘Ihble
Display
.............................
5-4
5-3. Inserting the Memory Card
.........................
5-11
5-4. Typical Limit-Line Display
.........................
5-19
5-5. The Completed Limit-Line Table
......................
5-21
5-6. Limit-Line Segments
............................
5-24
5-7. Segment Types
..............................
5-27
5-8. Upper and Lower Limit-Line Testing
....................
5-30
5-9. Analog+ Display Mode
...........................
5-32
5-10. Windows Display Mode
...........................
5-33
5-
11. Amplitude-Correction Display
.......................
5-35
5-
12. Completed Amplitude-Correction
Iable
...................
5-37
5-13. Amplitude-Correction Points
........................
5-38
6-1. Three Printouts Per Page
..........................
6-2
6-2. Plots Per Page
...............................
6-3
Contents-8