User`s guide

sweep time, 7-30
video bandwidth, 7-31
GHIJKL, 7-47
GND REF DETECTOR, 7-3, 7-47
graph markers, 7-48
GRAT ON OFF, 7-47
group delay and amplitude flatness (Option
ill), 10-9
GRPH MKR ON OFF, 7-48
GSMSOO measurements, 10-3
GSM/DCS-1800 firmware (Option 163), lo-11
guidelines for using Option 105, 4-26
H
hardware broken, A-l
hardware error messages, 9-7
hardware problems, 9- 1
harmonic band 0, 7-4
harmonic band 1, 7-4
harmonic band 2, 7-4
harmonic band 3, 7-4
harmonic band 4, 7-5
harmonic band menu, 7-12
harmonic band slope and offset adjust, 7-14
harmonic lock, 3-26, 7-13
highest peak
finding next, 7-58
highest signal peak, 7-80
HIGH SWEEP IN/OUT, 2-7
IIOLD, 2-8, 7-48
horizontal signal positioning, 7-31
how to call Hewlett-Packard, 9-4
how to return your analyzer for service, 9-6
HP 8590 Series key menus, 8-2-14
HP B&&W PRINTER, 7-78
HP-IB address, 7-10
HP-IB and Parallel (Option 041), 10-6
HP-IB cable, lo-15
HP-IB interface connector, 2-7
HP Paintjet, 7-61
improved amplitude accuracy (Option 053)
10-8
impulse noise
measurement, 3-17
increase frequency readout resolution, 3-6
informational messages, 9-7
INIT FLT, 7-2, 7-48
initial inspection, 1-3
INPUT 500, 2-3
INPUT 759, 2-3
input and output
auxiliary control, 7- 11
input attenuation control, 7-10
input impedance, 7-49
INPUT Z 509 750, 7-49
inserting a memory card, 2-19
installation, external keyboard, 5-42
installation manual
see User’s Guide, lo-12
instrument preset, 7-66
instrument state, 2-2
intensity control, 2-3
interface connectors, 2-7
intermodulation distortion, third order, 3-22
INTERNAL CARD, 7-49
internal comb generator, 7-27
internal/external leveling, 7-7
INTERNAL --+ STATE, 7-49
Internal --+ Trace, 7-49
INTERVAL CNTR INPUT, 2-6
K
keyboard
external keyboard functions, 5-40
keyboard, external, 5-40
keyboard operation, external, 5-42
key functions, external keyboard, 5-40
key menus, 8-l
knob, 2-3, 2-8
I
identifying distortion products, 3-20
identify the signal
FFT, 7-79
IDNUM, 7-2, 7-48
illegal spectrum analyzer command, A-l
impact cover (Option 040), 10-7
improved amplitude accuracy (Option 050),
10-8
improved amplitude accuracy (Option 051),
10-8
improved amplitude accuracy (Option 052),
10-8
label, softkey, 2-1
laserjet plots, 7-64
LAST SPAN, 7-49
length
GATE LENGTH, 7-46
level triggering, gate control, 7-46
limiters
RF and transient, lo-13
LIMIT FAIL, 5-18
limit-line functions, 5-22-28
limit lines, 5-18
amplitude coordinate, 5-25
cataloging, 7- 19
creating, 5-18, 5-22
Index-8