Technical data

Index
Index Index-3
equipment
cavity oscillator frequency
adjustment
, 3-25
display intensity correction
constants adjustment
, 6-7
EEPROM backup disk
procedure
, 3-33
fractional-N
frequency range adjustment
,
3-39
spur avoidance and FM
sideband adjustment
, 3-47
frequency accuracy adjustment
,
3-42
IF amplifier correction
constants adjustment
, 3-16
required
, 1-2
RF output power correction
constants adjustment
, 3-11
sampler magnitude adjustment
,
3-19
source spur avoidance tracking
adjustment
, 3-50
error messages, 5-17, 10-44
accessories
, 4-19
phase lock loop
, 7-6
receiver, 4-18
receiver failure
, 8-4
error terms
, 9-5, 11-2, 11-3
descriptions, 11-9
directivity (EDF and EDR)
, 11-9
inspection
, 11-8
isolation (crosstalk EXF and
EXR)
, 11-12
load match (ELF and ELR)
,
11-13
reflection tracking (ERF and
ERR)
, 11-11
source match (ESF and ESR)
,
11-10
transmission tracking (ETF and
ETR)
, 11-14
external
reference input
, 10-37
source mode
, 12-24
source mode frequency range
test
, 2-14
test sets
, 12-26
tests
, 10-10
F
failure
A1/A2 front panel
, 6-12
A11 phase lock and A3 source
check
, 7-8
error messages for receiver, 8-4
GPIB
, 6-19
key stuck
, 6-13
phase lock error
, 7-6
RF power from source, 7-5
fan
, 5-19
assembly
, 14-42
speeds, 5-19
voltages
, 5-19
faulty assembly
, 5-11
faulty data, 4-18
firmware revision softkey
, 10-41
FM Coil plot with 3 point sweep
,
7-29
FN LO at A12 check
, 7-16
FN LO waveform at A12J1
, 7-16
formatting conventions
, 1-iv
FRACN TUNE mode HI OUT
signal
, 7-27
fractional-N
check
, 7-20
frequency range adjustment
,
3-39
sequence
, 3-53
spur avoidance and FM
sideband adjustment
, 3-47
sequence
, 3-53
frequency
accuracy adjustment
, 3-42
counter
, 10-20
output in SRC tune mode
, 7-9
range and accuracy test, 2-4
range of fractional-N
adjustment
, 3-39
range, external source, 2-14
response (ratio) test
, 2-27
response test
, 2-23
front panel
assembly
, 13-18, 14-8, 14-10
key codes
, 6-13
LEDs
, 4-5
troubleshooting
, 6-12
G
GPIB
addresses
, 4-8
failures
, 6-19
service mnemonic definitions
,
10-42
system check
, 4-8
graphics processor
, 14-35
H
H MB line
, 7-24
hardware
, 13-26, 13-28, 13-29,
13-30
bottom view, 13-28
harmonic analysis
, 12-23
harmonics test
, 2-66, 2-70
HI OUT signal in FRACN TUNE
mode, 7-27
high band REF signal, 7-15
high quality comb tooth at 3 GHz
,
7-26
high stability frequency reference
(option 1D5) assembly
, 14-40
high/low band transition
adjustment
, 3-45
adjustment sequence
, 3-53
how to
adjust
ADC offset correction
constants
, 3-18
analog bus correction
constants
, 3-9
cavity oscillator frequency
correction constants
, 3-25
fractional-N frequency range
,
3-39
fractional-N spur avoidance
and FM sideband
, 3-47
frequency accuracy
, 3-42
high/low band transition, 3-45
IF amplifier correction
constants
, 3-16
option numbers correction
constants
, 3-31
RF output power correction
constants
, 3-11
sampler magnitude correction
constants
, 3-19
serial number correction
constants
, 3-30
source default correction
constants
, 3-7
source pretune correction
constants
, 3-10
source pretune default
correction constants
, 3-8
source spur avoidance
tracking
, 3-50
the analyzer
, 3-1
the analyzer using sequences
,
3-53
backup the EEPROM disk
, 3-33
check display intensity
, 6-7
initialize EEPROMs
, 3-32
load sequences from disk
, 3-53
position the A9 switch
, 3-6
retrieve correction constant data
fr o m E EP R OM back u p di sk
,
3-34
set up
high/low band transition
adjustments
, 3-54